background image

 

Installation Manual of Classic Solar Modules

 

 

 

www.canadiansolar.com       

Rev IM/GN-CM-EN/1.0          Copyright© October, 2020 Canadian Solar Inc.        1

 

1.0    GENERAL INFORMATION

 

This  general  manual  provides  important  safety  information  relating  to  the  installation,  maintenance  and 
handling of CS-series solar modules.   
Professional installer must read these guidelines carefully and strictly follow these instructions. Failure to follow 
these instructions may result in death, injury or property damage. The installation and handling of PV modules 
requires professional skills and should only be performed by qualified professionals. The installers must inform 
end-users (consumers) the aforesaid information accordingly. The word "module" or "PV module" used in this 
manual refers to one or more CS-series solar modules. 
This  manual  is  only  valid  for  the  classic  module  types  CS5AH-M,  CS5PH-M,  CS5PH-P,  CS6AH-P,  CS6AH-M, 
CS6PH-P, CS6PH-M, CS6XH-P and CS6XH-M. 
Please retain this manual for future reference. We recommend checking www.canadiansolar.com regularly for 
the most updated version. 

 

1.1    INSTALLATION MANUAL DISCLAIMER 

The  information  contained  in  this  manual  is  subject  to  change  by  Canadian  Solar  Inc.  without  prior  notice. 
Canadian Solar Inc. gives no warranty of any kind whatsoever, either explicitly or implicitly, with respect to the 
information contained herein.   
In  the event  of any  inconsistency  among  different  language  versions  of  this  document,  the  English      version 
shall  prevail.  Please  refer  to  our  product  lists  and  documents  published  on  our  website  at: 
http://www.canadiansolar.com as these lists are updated on a regular basis. 
 

1.2    LIMITATION OF LIABILITY 

Canadian Solar Inc. shall not be held responsible for damages of any kind, including – without limitation – bodily 
harm, injury or damage to property, in connection with handling PV modules, system installation, or compliance 
or non-compliance with the instructions set forth in this manual. 
 

2.0    SAFETY PRECAUTIONS 

Warning:  Before  attempting  to  install,  wire,  operate  and/or  service  the  module  and  other 
electrical equipment, all instructions should be read and understood. PV module connectors 
pass  direct  current  (DC)  when  exposed  to  sunlight  or  other  light  sources.  Contact  with 
electrically  active  parts  of  the  module,  such  as  terminals,  can  result  in  injury  or  death, 
irrespective  of  whether  or  not  the  module  and  the  other  electrical  equipment  have  been 

connected.   

Avertissement:  Toutes  les  instructions  devront  être  lues  et  comprises  avant  de  procéder  à 
l’installation,  le  câblage,  l’exploitation  et/ou  l’entretien  des  panneaux.  Les  interconnexions 
des panneaux conduisent du courant continu (CC) lorsque le panneau est exposé à la lumière 
du soleil ou à d’autres sources lumineuses. Tout contact avec des éléments sous tension du 
panneau  tels  que  ses  bornes  de  sortie  peut  entraîner  des  blessures  ou  la  mort,  que  le 

panneau soit connecté ou non. 

General Safety 

 

All modules must be installed by licensed electricians in accordance to the applicable electrical codes such 

Summary of Contents for CS5AH-180M



















Reviews: