background image

CPB-515 Operation and Maintenance Manual 

– TTS 45, 70, 80,100, 110 Series (10-2017)

  

12

 

 

 

IMPORTANT:

  Locate the identification tags, as shown above, on both undercarriages, 

and record the model number and serial numbers on warranty certificate for your records. 

 

3. 

Raise and support implement such that the rear tires are just off the ground. 

 

 

IMPORTANT

 

Safety of the installation depends on the right operation in lifting 
and supporting the machine. Check the work area thoroughly and 
work in a level area. Respect safe operating practices, operate in 
conditions of enough light. Make sure the free spaces of the work 
area are suitable for the dimensions of the parts to be handled and 
for the lifting equipment maneuvers. Be careful: risk of injury. 

 

 

4. 

Remove the tire and rim assemblies. 

 

5. 

Remove the axle and hub assemblies from the implement frame (as required).

 

 

6. 

Install track fitment axle.  For two axle midroller track systems, make sure the 
stabilizer brackets on the axle are facing to the front of the implement.  Tighten 
mounting hardware. 

 

 

WARNING

 

Danger of crushing. Use suitable lifting devices (capacity at least 
9000 lbs (4100Kg)), wear safety equipment and observe the safety 
rules. 

In case of fork lift use for handling operations, be careful not to 
damage the rubber track. Metal chains or cables are not 
recommended. 

 

Serial # Plate 

Summary of Contents for 100-3613

























Reviews: