background image

Specifications are subject to without notice.

Model

PAL

NTSC

Image Sensor 
Total Pixels 
Effective pixels
Scanning system 
Scanning Frequency 
Sync. System 
Horizontal Resolution 
Min. illumination 
Video Output 
S/N Ratio
Exposure 
Lens 
Gain Control 
Shutter Speed 
Digital Slow Shutter 
Flickerless 
Brightness 
Digital Wide Dynamic Range
Defog
Backlight Compensation
Highlight Compensation
Day & Night 
White Balance 
Gamma
Chroma
Digital Noise Reduction
Mirror

1020(H) × 508(V)

976(H) × 494(V)

15.734KHz(H),59.94Hz(V)

1/60 ~ 1/120,000 sec

1/50 ~ 1/120,000 sec 

1020(H) x 596(V)

976(H) x 582(V)

15.625KHz(H),50Hz(V)

1/3” 2:1 Interlaced CCD

2:1 Interlace

Internal

Max 700 TV lines in color

Color : 0.3 Lux, BW : 0.1 lux

1.0 Vp-p (75 ohm, composite)

more than 50dB (AGC off)

ALC / ELC

DC / Manual

Off / On (0 ~ 20 steps)

Off / On (x2 ~ x512)

Off  / On

1 ~ 20 steps

Off / Manual / Auto
Off / Manual / Auto

Off / On
Off / On

Day / Night / Auto / EXT / CDS

ATW / Push / Manual

0.35 ~ 0.70

1 ~ 20 steps

Off / Low / Middle /High

Off / On

1 ~ 20 steps

Positive / Negative

1 ~ 20 steps

Off / 8 positions 
Off / 4 positions 

One Push

Coaxial control, RS-485

COAX : Pelco-C / RS-485 : Palco-D, Pelco-P

Disp Sel / Set Title / Language / Setup Status

ID / Title

0 ~ 9 , A ~ Z , a ~ z

English 

DC12V±10%

Max 700mA 

-10

 ~ +50

0 ~ 86% (non-condencing)

-20

 ~ +60

Model

PAL

NTSC

Sharpness
Effect 
Shading
Privacy Mask 
Motion Detection 
Defect Detection
Communication
Protocol
Display
Disp Sel
OSD Text 
Language
Power Source 
Power Consumption 
Operating Temperature 
Operating Humidity 
Storage Temperature

47 

Specifications “CS-PD710IR”

Specifications “CS-PD710IR”

46

Summary of Contents for CS-PD710IR




























Reviews: