Campingaz PARTY-GRILL R, Manual

Page: 6 / 40

Consumption: 99 g/h (1.36 kW) - injector n° 015556
Category: direct butane pressure.
Thank you for having chosen this Campingaz
®
PARTY-GRILL R.
A - IMPORTANT: YOU ARE USING GAS,
TAKE GREAT CARE !
The purpose of these directions for use is to enable you
to use your Campingaz
®
“ PARTY-GRILL R ” appliance
properly and in complete safety.
Please read them carefully, so as to familiarise yourself
with the appliance before assembling it onto its gas
container.
Please follow the instructions that appear in these
directions for use. Any failure to follow these
instructions may pose a danger both to the user and
to people in the vicinity.
Always keep these directions for use in a safe place
so that you can refer to them if need be.
This appliance must only be used with Campingaz
®
cylinders 901, 904 and 907. It may be dangerous to
use any other gas containers.
La Société Application Des Gaz will not accept any
liability in the event that a cylinder manufactured by
any other brand is used.
This equipment should only be used outside
premises and kept away from inflammable materials.
Do not use an appliance that is leaking, not working
properly or damaged. Return it to the shop you
bought it from, which will give you details of the
nearest after-sales service outlet.
Never modify this appliance or use it for applications
for which it is not intended.
Do not use this product in caravans, cars, tents,
huts, sheds or any small enclosed areas.
The product should not be used while sleeping or
left unattended.
This product consumes fuel through combustion
or consumption of oxygen and gives off certain
substances and gas, which could be dangerous
such as carbon monoxide (CO).
Carbon monoxide is an odorless, clear gas that
can cause flu-like symptoms, sickness, illness,
and possibly death if produced inside aforesaid
enclosed areas through use of the product without
proper ventilation.
B - PUTTING THE APPLIANCE INTO SERVICE
Take the appliance out of its packaging, and remove the
lid (2), hotplate (3) pan support (crosspieces) (4) and
water container (5)
C - FITTING TO CAMPINGAZ
®
CYLINDERS
901, 904 and 907
(If an empty cylinder is in place, read section H:
“Removing or changing the cylinder”)
When inserting or removing a cylinder, always do so in
an airy location, preferably outside and never close to a
naked flame, heat source or spark (cigarette, electrical
appliance, etc.), and well away from any other people
and inflammable materials.
a) Check that the stove seal (1) and the tap thread (1a)
(see fig.1) are in place and in good condition.
b) Do not use the stove if the seal is missing or damaged:
return it to your stockist.
c) Check that the gas inlet is fully closed by turning the
control knob (7) clockwise as far as the stop (direction
“-” of the arrow).
d) Position the cylinder on a horizontal and solid surface,
then remove the cap.
e) Take the tap/burner unit (8) and screw it as far as it will
go onto the cylinder valve (9) (fig.3)
If you detect a leak (i.e. you can smell gas before the tap is
opened), place the appliance outside immediately, in a well-
ventilated location free of any ignition sources, where the
leak can be diagnosed and stopped. If you wish to check the
tightness of your appliance, you should do so outside. Use
gas leak solution, not a naked flame, to search for any leaks.
D - ASSEMBLING THE CAMPINGAZ
®
PARTY-
GRILL R STOVE
a) Fit the water container (5): connect it securely by turning
as far as the stop, following the arrow marked “v” (fig.4).
b) Check whether the burner (6) is properly fitted (fig.4).
c) Put the crosspieces in place (4).
E - PREPARING TO USE THE “HOTPLATE”
FUNCTION
a) Place approximately 3/4 of litre of water in the water
container (5). The level should remain a few millimetres
below the top of the central vent: (fig.4) “maxi” mark.
b) Position the hotplate (3) by indexing the notches on the
crosspieces (4).
F - USING THE PARTY-GRILL AS A “HOT-
PLATE” (fig.7a)
1) Lighting the burner
a)
Open the tap by turning it (7) anti-clockwise: 1
rotation maximum.
b)
Press the button (7) with the thumb until the piezo
system operates. This is made easy if the other
fingers are placed in the slot provided. (fig.5)
c)
If the burner flame is not visible under the hot-plate,
(fig.5), recommence the procedure “b”.
d)
After 3 attempts, close the tap by turning it clockwise
as far as it will go. Check that the cylinder contains
gas and start the lighting operations a) and b) again.
Operation and maintenance
Figures 1 to 7 : see page 2
6
GB