background image

MSX10, MSX20, MSX20R, MSX30R, and MSX50R Solar Panels 

some batteries are discharged below a specified voltage, the battery becomes 
damaged and cannot be recharged. 

The battery supplies power directly to the operating system, the solar panel 
supplies power to recharge the battery.  Therefore, on the average, the solar panel 
must provide at least as much power to the battery as is being used by the system. 

The battery must have enough capacity to power the system during times of no 
charging (night) or low charging (stormy winter days). 

5.2  Voltage Regulator 

The solar panel must be regulated either with a Campbell Scientific regulator or an 
attached regulator.  The regulator has two basic functions:  1) blocks any current 
flow from the battery to the solar panel, and 2) limits the source current to the 
battery. 

The MSX10 is unregulated and must be connected to a Campbell Scientific 
voltage regulator.  These regulators include the PS100, PS12LA, PS512M, 
CH12R, CH512R, CH100, CR23X rechargeable base, 21XL base, CR200 series 
dataloggers, and the CR7 solar panel input. 

The MSX20R, MSX30R, and MSX50R have a voltage regulator attached.  These 
panels are connected directly to a battery. 

 

 

This is a blank page.

Summary of Contents for MSX10














Reviews: