background image

 

MSX10, MSX20, MSX20R, MSX30R, and 
MSX50R Solar Panels 

1.  General

 

The solar panel is a photovoltaic power source used for charging lead acid 
batteries.  The MSX10, MSX20, MSX20R, MSX30R, and MSX50R are 10, 
20, 20, 30, and 50-watt solar panels, respectively. 

The MSX10 Solar Panels has two leads stripped and tinned to insert into the 
terminals labeled 'CHG' on the PS100 or PS12LA Charging Regulator.  With a 
CR7, the two wires from the solar panel are inserted into the terminals marked 
SOLAR PANEL located underneath the 700X Control Module.  An external 
lead acid battery can be connected to the CR7 at the terminals marked 
EXTERNAL BATTERY next to the SOLAR PANEL terminals. 

The MSX20R, MSX30R, and MSX50R are regulated solar panels with two 
stripped and tinned leads for direct connection to an external 12-volt lead acid 
battery. 

2.  Specifications 

 MSX10 

MSX20/ 

MSX20R 

MSX30R 

MSX50R 

Typical peak power (Pp) 

10 W 

20 W 

30W 

50W 

Voltage @ peak power (Vpp) 

(voltage from solar panel before regulator)

 

17.1 V 

17.1 V 

17.1 

17.5 

Current @ peak power (Ipp) 

0.60 A 

1.17 A 

1.75 A 

2.9 A 

Guaranteed minimum peak power 

10 W 

20 W 

30 

50 

Approximate effect of temperature on 

power 

 

-0.37%/

°

 

-0.38%/

°

 

-.38/

°

 

-.38/

°

Length, cm 

42.0 

50.1 

59.2 

83.9 

Width, cm 

26.9 

42.0 

50.1 

53.7 

Depth, cm 

2.3 

5.0 

Weight, kg 

1.50 

2.95 

5.29 

6.0 

 

The above solar panel characteristics assume a 1 kilowatt per 
square meter illumination and a solar panel temperature of 25

°

C.  

Individual panels may vary up to 10%.  The output panel voltage 
increases as the panel temperature decreases. 

NOTE 

3.  Installation 

3.1  Mounting

 

The panel should be mounted facing south if located in the Northern 
Hemisphere, or facing north in the Southern Hemisphere.  The solar panel 
mounts to the mast or leg of the CM10/CM6 Tripod, or any 1 5/8" schedule 40 

Summary of Contents for MSX10














Reviews: