manualshive.com logo in svg

Campbell AL205E, Product Manual

Share
Download
Campbell AL205E Product Manual Download Page 28

ALERT2 Originating IND - Modulator & Data Encoder

Serial 0 = API or ALERT
Serial 1 = API or ALERT
Console Port = Enableable for ALERT Concentration

Hardware Rev2
GPS Chip Baud 9600 (normal)
Ver. 6.1.1, Date Jul 12 2019, Time 10:14:42
Copyright (c) Blue Water Design LLC 2007 - 2017
AirLink Version 2.0.0
Chip Locked
Successfully loaded 136 bytes from flash

PARAMETERS LOADED CORRECTLY FROM FLASH

** IND Device Configuration
IND Address (1...65534).............................= 9,000
GPS period (min)....................................= 30
GPS fail time (min).................................= 5
FEC mode (0, 1, 2)..................................= 0
Low Power Mode......................................= 1 (Yes)
Always High Speed Mode..............................= 0 (No)

Serial Port 0 Configuration
Port 0 Configuration................................= 0 (API input)
Port 0 Independent Source Address Enabled?..........= 0 (No)
Port 0 Source Address...............................= 9,000
Port 0 Baud Rate....................................= 57,600
Port 0 Parity.......................................= 0 (none)
Port 0 Stop bits....................................= 1

Serial Port 1 Configuration
Port 1 Configuration................................= 0 (API input)
Port 1 Independent Source Address Enabled?..........= 0 (No)
Port 1 Source Address...............................= 9,001
Port 1 Baud Rate....................................= 57,600
Port 1 Parity.......................................= 0 (none)
Port 1 Stop bits....................................= 1

Serial Console Port Configuration
Console Port Debug Output...........................= 1 (Yes)
Console Port Data Input Enabled?....................= 0 (No)

**Originating IND MANT Header Configuration
Originating IND Dflt Destination Address (1...65534)= 9,999
Originating IND Add Time Service Request............= 1 (Yes)
Originating IND Add Path Service Request............= 1 (Yes)
Originating IND Hop Limit...........................= 1
Originating IND Add Destination Address ............= 0 (No)
Encrypt Outgoing Packets............................= 0 (No)
Encryption Key......................................= XXXXXXXXXXXXXXXX
Pending Encryption Key..............................= XXXXXXXXXXXXXXXX

AL205E ALERT2 Encoder

26

Summary of Contents for AL205E





































Reviews:

No comments

Brands by name

Popular brands

Load more brands