Campbell Hausfeld WK250000AV, Operating Instructions And Parts Manual

Page: 1 / 48

Operating Instructions and Parts Manual
Inverter Plasma Cutter
IN975000AV 2/12 © 2012 Campbell Hausfeld/Scott Fetzer For parts, product & service information
visit
www.chpower.com
WK250000AV
Table of Contents
Description . . . . . . . . . . . . . . . . . . . . . . . . . 1
Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . 1
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Guidelines . . . . . . . . . . . . . . . . . . . . 2
Safety Symbols . . . . . . . . . . . . . . . . . . . . . . 2
Important Safety Information . . . . . 2 - 5
Definitions of Terms
and Symbols . . . . . . . . . . . . . . . . . . . . . . . . 6
Setup and Components . . . . . . . . . . . 7 - 8
Operation . . . . . . . . . . . . . . . . . . . . . . 9 - 10
Maintenance. . . . . . . . . . . . . . . . . . . . . . . 11
Troubleshooting Chart . . . . . . . . . . . . . . 11
Service Record . . . . . . . . . . . . . . . . . . . . . 12
Replacement Parts. . . . . . . . . . . . . . . . . . 13
Wiring Diagram . . . . . . . . . . . . . . . . . . . . 14
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Description
This Campbell Hausfeld Inverter Plasma Cutter is designed to be powered by a
dedicated 120V AC, 20 Amp (recommended), 60 hertz grounded outlet, and a
(recommended) minimum air supply of 1.25 CFM [35 L/min] @ 40 psi [276 kPa].
This Plasma Cutter is equipped with a 10 foot [3 m] power cord, a 13-3/4 foot [4.2 m]
torch cable, and a 10 foot [3 m] clamp cable. As delivered from the factory, this Plasma
Cutter is rated to clean cut mild steel up to 1/8 inch [3.2 mm] thick, rough sever cut
mild steel up to 1/4 inch [6.4mm] thick, and has a 60% duty cycle rating.
Unpacking
After unpacking the unit, inspect carefully for any damage that may have occurred
during transit. Make sure to tighten fittings, bolts, etc., before putting unit into service.
Report any missing items by calling 1-800-746-5641.
Do not operate unit if damaged during shipping, handling or use.
Damage could result in bursting and cause injury or property damage.
Failure to follow these instructions may result in property damage
and / or bodily injury.
RETAIN THIS INFORMATION FOR FUTURE REFERENCE
Serial Number:
Model Number:
Date of Purchase:
REMINDER: Keep your dated proof of purchase for warranty purposes!
Attach it to this manual or file it for safekeeping.
Specifications
Rated input voltage . . . . 1ph ~ 120 V
Power frequency . . . . . . . . . 60 Hz
Rated input current . . . . . . . 18.5 A
Rated input power . . . . . . . 2.2 KVA
No-load voltage . . . . . . . . 300 V dc
Cutting current . . . . . . . . . . . 13 A
Rated duty cycle . . . . . . . . . . 60%
Efficiency (rated conditions) .
≥
0.85
Insulation grade . . . . . . . . . . . . B
Protection grade . . . . . . . . . IP21S
Cutting thickness
(carbon plate) . . . . . . . . .
≤
6 mm
Weight . . . . . . . . . . . . . . . 22 lbs.