5
SB514000
www.chpower.com
Operating The Tool
(Continued)
1 . The air
compressor
must be able
to maintain a
minimum of 60
psi when the
tool is being used . An inadequate air
supply can cause a loss of power and
inconsistent driving .
2 . An oiler can be used to
provide oil circulation
through the tool . A
filter can be used to
remove liquid and solid
impurities which can rust or “gum
up” internal parts of the tool .
3 . Use 3/8 inch air hoses
with a minimum
working pressure of
150 psi . Use 1/2 inch
air hoses for 50' run
or longer . For better performance,
install a 3/8 inch quick plug (1/4 inch
NPT threads) with an inside diameter
of .315 inch (8mm) on the tool and
a 3/8 inch quick coupler on the air
hose .
4 . Use a pressure regulator on the
compressor, with an operating
pressure of 0 -125 psi . A pressure
regulator is required to control
the operating pressure of the tool
between 60 and 100 psi .
SINGle
SeqUeNTIal
MODe
This mode
requires the
trigger to be
pulled each time a fastener is driven .
The tool can be actuated by depressing
the WCE against the work surface
followed by pulling the trigger .
The trigger must be released to reset
the tool before another fastener can be
driven .
CheCKING The WORK CONTaCT
eleMeNT (WCe)
Check the operation
of the Work Contact
Element (WCE) trip mechanism before each
use. The WCE must move freely without
binding through its entire travel distance.
The WCE spring must return the WCE to
its fully extended position after being
depressed. Do not operate the tool if the WCE
trip mechanism is not operating properly.
Personal injury may occur.
1 . Disconnect the air
supply from the tool .
2 . Remove all
fasteners
from the
magazine
(see
Loading/ Unloading) .
3 . Make sure the trigger
and work contact
element (WCE) move
freely up and down
without sticking or
binding .
4 . Reconnect
air supply
to the
tool .
5 . Depress the Work
Contact Element
(WCE) against the
work surface without
pulling the trigger . The
tool
MUST NOT OPeRaTe
. Do not
use the tool if it operates without
pulling the trigger . Personal injury
may result .
6 . Remove the tool from
the work surface .
The Work Contact
Element (WCE) must
return to its original
down position . The tool
MUST NOT
OPeRaTe
. Do not use the tool if it
operates while lifted from the work
surface . Personal injury may result .
7 . Pull the
trigger
and
depress
the work
contact element (WCE) against the
work surface . The tool
MUST NOT
OPeRaTe
.
8 . Depress
the Work
Contact
Element
(WCE)
against the work surface . Pull the
trigger . The tool
MUST OPeRaTe
.
An improperly
functioning tool must
not be used. Do not actuate the tool unless the
tool is placed firmly against the work piece.
lOaDING/UNlOaDING The TOOl
1 . Always
disconnect
the tool from
the air supply
before
loading
fasteners .
2 . Push
down on
the latch
button .
Pull back on the magazine cover .
3a . For nails,
insert a
stick of
Campbell
Hausfeld
nails or equivalent (see “Fasteners”
section) into the magazine . Make
sure the pointed ends of the
fasteners are resting on the bottom
ledge of the magazine when
loading . Make sure the nails are not
dirty or damaged .
3b . For
staples,
load a clip
of staples
with the
crowns straddling the magazine rail .
4 . Push the
magazine
cover
forward
until latch
button pops up .
5 . Always unload all fasteners before
removing tool from service .
Unloading is the reverse of loading,
except that you must
disconnect
the air supply before unloading .
aDJUSTING The FaSTeNeR
PeNeTRaTION
The tool is equipped with an adjustable
depth of drive feature . This allows the
60 psi
Min .
120 psi
Max .
150 psi WP
3/8 inch
I .D .
Latch
button
Magazine rail
