manualshive.com logo in svg

CAMPAGNOLO Ekar 13S Rear Derailleur, Technical Manual

Share
Download
CAMPAGNOLO Ekar 13S Rear Derailleur Technical Manual Download Page 4

REAR DERAILLEUR - Rev. 00/ 09-2020

CAMPAGNOLO COMPONENTS - TECHNICAL MANUAL

4

3 - INTERFACE WITH THE FRAME 

3.1 - STANDARD DROP-OUT SPECIFICATIONS

The stroke of the cage in relation to the cable throw is checked 

by Campagnolo Quality Control for each single piece produced.

The distance of the rear derailleur hanger from the first sprocket 

influences this stroke, so it is indispensable to stay within the to

-

lerance prescribed as per the drawing (Fig. 1). 

WARNING!

Campagnolo

®

 rear derailleurs are designed to work with dro-

pouts that have the dimensions shown in Fig. 2.

For your safety and for the performance of the drivetrain 

please make sure that the dropout of your bicycle has those 

dimensions.

If you have any doubts please have a qualified mechanic 

inspect your bike before using it.

Drop-outs outside these specifications can lead to a serious 

loss of performance.

10,2 - 12,2 mm max

R max = 8,8

L

B

X

L = 24 ÷ 28 mm
X = 4 ÷ 8 mm
B = 25° ÷ 35°

R max = 1

10,2 - 12,2 mm max

L = 24 ÷ 28 mm

X = 4 ÷ 8 mm

B = 25° ÷ 35°

R max = 8,8

R max = 1

L

B

X

Fig.1

Fig.2

3.2 -FRAME SPECIFICATIONS

Fig.3

B

Height of the chain stays near 

the sprocket pack: B < 7 mm

Summary of Contents for Ekar 13S Rear Derailleur













Reviews:

No comments

Brands by name

Popular brands

Load more brands