background image

7

GRILL OPERATION

Before using the grill for the first time, let it run at maximum temperature for the duration of 15 minutes.

For best results it is advisable to preheat for a few minutes the grill.

OVEN OPERATION

Before  using  oven  for  the  first  time,  let  it  run  at  maximum  temperature  for  the  duration  of  30  minutes, 

without foodstuffs inside.

In the event of the burner flame being accidentaly extinguished, turn off the burner control knob and do not 

attempt re-ignite the burner for at least 1 min.

For ovens with thermostat the different positions of the knob correspond to the following temperatures 

in °C of the oven.

POSITION

 

6

TEMPERATURE

 

130 

160 

180 

200 

220 

240

CAUTION:

WHEN GRILLING, GRILL COMPARTMENT DOOR MUST BE LEFT COMPLETELY 

OPEN. 

DURING AND IMMEDIATELY AFTER USE ACCESSIBLE PARTS MAY BE HOT; DO 

NOT TOUCH THEM AND KEEP CHILDREN AWAY.

GLASS  LIDS  MAY  SHATTER WHEN  HEATED. TURN ALL THE  BURNERS  OFF 

BEFORE CLOSING THE LID. 

During grill operation, do not obstruct the hole in the centre of the burners where 

heat and smoke can come out. 

NOTE: 

UNDER  NO  CIRCUMSTANCES  ARE  CLEANING  PRODUCTS/  FLAMMABLE 

(PETROL, KEROSENE, ALCOHOL BASED PRODUCTS, AEROSOLS) MATERIALS 

TO BE STORED. USE COMPARTMENT FOR UTENSIL STORAGE ONLY.

Summary of Contents for SMEV 401





















Reviews: