CAME LHS A/01 Installation And Configuration Manual Download Page 3

Page: 3 / 32

age

- Manual

FA01639-EN

- 12/2021 - © C

AME S.p.A. - The contents of this manual may be changed at any time and without notice. - T

ranslation of the o

riginal instructions

PRODUCT DATA AND INFORMATION

Description

LHS A/01 (840AA-0060)

Monolith intercom entry panel for X1 system expandable up to 4 calls.

LHS V/01 (840AA-0040)

Monolith video entry panel for X1 system expandable up to 4 calls.

LHS V/01 PLUS (840AA-0050)

Monolith video entry panel for X1 system expandable up to 4 calls, with Bluetooth and built-in RFID reader for access control.

Description of parts

Video camera lens*

Front cover

Button

Hole cover

Microphone

Front cover fastening screw

Back

Wiring hole

Screws and expansion plugs

Optional accessories

Rain cover

Recessed-mount proﬁ le and frame

Back box

Single button

Double button

* Video versions only (840AA-0050/840AA-0040)

Summary of Contents for LHS A/01

































Search results

Summary of Contents for LHS A/01

Reviews:

Related manuals for LHS A/01

Brands by name

Popular brands

CAME LHS A/01, Installation And Configuration Manual

Search results

Summary of Contents for LHS A/01

Reviews:

Related manuals for LHS A/01

Brands by name

Popular brands