manualshive.com logo in svg

CAME LHS A/01, Installation And Configuration Manual

Share
Download
CAME LHS A/01 Installation And Configuration Manual Download Page 21

P

age 

21

 - Manual 

FA01639-EN

  - 12/2021 - © C

AME S.p.A. - The contents of this manual may be changed at any time and without notice. - T

ranslation of the o

riginal instructions

PROGRAMMING ENTRY PANELS WITH VA/01 AND A/01

Entering programming mode

+

–

M1

+

PROG

Press and hold the power supply unit [PROG] button for at least 3 seconds.
The 

   

   LEDswill fl ash together with the [P1-P4] button LEDs.

The [PROG] LED on the power supply unit and entry panel turn on and stay on.

Programming call buttons

Press [P1] to confi gure 2 x two-way buttons (max 4 calls).
Press [P2] to confi gure two single buttons (max 2 calls).
The 

 LED and the call button LEDs will stop fl ashing.

Programming calls

1

2

In [Programming calls], the 

 LED and the [PROG] LEDs fl ash.

The call button LEDs will remain on.

 In a system with multiple entry panels, you can only program one entry panel at a time only, identifi ed by the lit 

 LED.

On the remaining entry panels, the 

 LED will remain on.

Summary of Contents for LHS A/01

































Reviews:

No comments

Brands by name

Popular brands

Load more brands