background image

FA00008-EN v.7 – 05/2017 

25 

CAME S.p.A. 

 

Display 

Description 

Factory settings 

TALK 

LOCK 
ADVANCE 
TIME 

Time advance operating electric lock. Choose between the minimum and maximum values: 
minimum value = 0,5 s 
maximum value = 5,0 s 

0.5 

TRLK 

LOCK 
OPERATION 
TIME 

Operating time of the electric lock. Choose between the minimum and maximum values: 
minimum value = 0,5 s 
maximum value = 5,0 s 

0.5 

LKSH 

LOCK 
HOOKING 

Setting of closing push for hooking the electric lock. Choose between the following values: 
NO = no push 
MIN = light push 
MED = medium push 
MAX = heavy push 

MED 

PUCL 

PUSH DOOR 
CLOSED

 

Setting the push on the closed mechanical stop. Choose between the following values: 
NO = no push 
MIN = light push 
MED = medium push 
MAX = heavy push 
XMAX = very heavy push 

MIN 

PIPP 

PUSH DOOR 
OPEN 

Setting of the opening push. Choose between the following values: 
NO = no push 
YES = push enabled (disabled with ANG) 

NO 

HOLD 

HOLD DOOR 
OPEN 

Setting the push of keeping the door open. Choose between the following values: 
NO = no push 
MIN = light push 
MED = medium push 
MAX = heavy push 

MED 

PUGO 

PUSH & GO 

Push opening activation. Choose between the following values: 
NO = off 
YES = active (disabled with PWAS) 

YES 

PWAS 

POWER 
ASSIST 

Manual operation of the door in servo assisted mode (Note: any safety devices are disabled). Choose 
between the following values: 
NO = disabled manual operation power-assisted 
MIN = minimum manual operation power-assisted 
MED = medium manual operation power-assisted 
MAX = maximum manual operation power-assisted 

NO 

ANG 

OPENING 
ANGLE 

Selecting of the door opening angle. Choose between the following values: 
NO = the door opens up to the mechanical opening stop 
5 … 240 = the door opens up to the selected angle 
(Note: the value indicated refers to the arm angle and not to the door angle) 

NO 

TAKO 

KO-CLOSING 
TIME

 

Open door time setting, after the 1-KO command. Choose between the minimum and maximum: 
minimum value = 1 s 
maximum value = 30 s 
NO = the door is always open 
NO = see MENU > TAC 

NO 

MOT 

MOTOR 
CIRCUIT 

Setting the manual friction of the door, by means of the electrical connection of the motor windings. 
Choose between the following values: 
OC = manual door opening without friction (motor with open circuit windings) 
SC = manual door opening with friction (motor with short-circuit windings) 

SC 

 
 

 

Summary of Contents for FLUO-SW



































Reviews: