CAMBRIDGE DL-CSW-10AT-LFT Installation, Setup And Operation Download Page 13

Page: 13 / 22

1.1 SOFTWARE NAVIGATION FLOWCHART (CONTINUED)

Motion Display

S10

ZERO BAND

S11

ZERO DELAY

S12

Zero Tracking

S13

Tracking Delay

S14

Display lb/kg

S15

Scale ID

S16

Brightness

S17

Sleep Mode

S18

Angle limit

END

Normal, Blank,

Dashes (Normal)

1-99

Divisions (2)

0-99

Updates

(2)

1 - 99

Divisions

(1)

1 - 99

1/4 Sec. Incriments

(0)

lb, kg, lb/kg

(lb/kg)

1 - 99

RF Link Output

(1)

1 - 15

15 is Brightest

(15)

0 - 30 Min.

Display turns off

(0 Min.)

+/- (0 - 9 Degree)

+/- (6 Deg.)

1.2 NAVIGATION KEYS

During setup you will be required to make numeric entries. (Ex: Capacity, Zero Band, etc...)

The following table outlines the keys used to perform these entries along with their function.

ZERO-------KEY IS USED TO NAVIGATE UP.
GRS/NET---KEY IS USED TO NAVIGATE DOWN.
TARE--------KEY IS USED TO NAVIGATE LEFT.
lb/kg---------KEY IS USED TO NAVIGATE RIGHT.
PRINT-------KEY IS USED TO ENTER DATA AND RETURNS.

Summary of Contents for DL-CSW-10AT-LFT























Search results

Summary of Contents for DL-CSW-10AT-LFT

Reviews:

Related manuals for DL-CSW-10AT-LFT

Brands by name

Popular brands

CAMBRIDGE DL-CSW-10AT-LFT, Installation, Setup And Operation

Search results

Summary of Contents for DL-CSW-10AT-LFT

Reviews:

Related manuals for DL-CSW-10AT-LFT

Brands by name

Popular brands