Cambium Networks RFU-C Installation Manual Download Page 66

Page: 66 / 68

Chapter 6: RFU-C Configurations

4+4 Dual Polarization – Remote Mount Installation

phn-4026 003v000

Page 6-41

12 Mount the two O-Rings (supplied in the RFU-C Symmetrical Coupler kit). Mount the two RFU-C

radio units on each RFU-C symmetrical coupler by tightening the four M8 captive screws and

washers (supplied assembled in the RFU-C radio).

Note

RFU-C mounting screws and washers can be supplied either assembled on the RFU-C, or as a part of
the RFU-C kit.

13 Connect the flexible waveguide to the RFU-C Symmetrical coupler using the O-Ring and screws (supplied

with the flexible waveguide kit). Connect the other end of the Flexible Waveguide to one radio port

polarization of RFU-C OMT.

14 Repeat paragraphs 7 through 13 for the second polarization.

Summary of Contents for RFU-C





































































Search results

Summary of Contents for RFU-C

Reviews:

Related manuals for RFU-C

Brands by name

Popular brands

Cambium Networks RFU-C, Installation Manual

Search results

Summary of Contents for RFU-C

Reviews:

Related manuals for RFU-C

Brands by name

Popular brands