![background image](http://html1.mh-extra.com/html/calpeda/mxv-b-series/mxv-b-series_original-operating-instructions_4047595016.webp)
10.2.
Axial position of the pump rotor
MXV(L), MXV(L)4
In the vertical position and from the resting position
(
fig.5a
), raise the rotor, levering on a pin inserted in the
hole in the shaft, until the pin can be rested under the
coupling (64.22).
In this position (
fig. 5b
), by tightening the screws (64.25)
uniformly, the shaft (64.00) is locked tight in the coupling.
Remove the pin.
Mount the motor as indicated in
section 4
.
11. Horizontal installation MXV(L) 50-65-80,
MXV(L)4 50-65-80
11.1 Connection of support feet
For the mounting of the support feet all tour nuts (61.04)
on the tie-bolts (61.02) must be removed (see cross-sec-
tion drawing in
section 14.
).
ATTENTiON: do not loosen only the two nuts
on the
side of the upper cover to which the support foot is to be
attached.
To remove the 4 nuts (61.04) the lantern bracket
(32.00) must be removed.
With the pump in the vertical
position, carry out dismantling sequences 1 - 6 in
section 9
.
Remove the washers (61.03) and attach the support foot
(61.30) on the side of the upper cover (34.02) in the ap-
propriate position depending on the directional arrange-
ment of the pump casing (14.00) suitable for the system:
suction on the left and delivery on the right, or vice-versa
(
fig.6
)
Do not insert the two washers (61.03) on the support foot
when the tie-bolts (61.02) do not protrude from the nuts
(61.04).
The 4 nuts must be uniformly tightened with alternat-
ed crossover tightening procedure in diametrically
opposite positions
. Tightening torque as per
section
10.1
.
Mount the lantern bracket (32.00) with the coupling
(64.22) and position the pump shaft as indicated in
sec-
tion 10.2
.
Mount the motor as indicated in
section 4
, and orientate
the terminal board with respect to the support foot
(61.30) in the position most suitable for the system.
After setting the pump in the horizontal position, fix the
second support (61.30) to the base (61.00), with the
screws (61.30), washers (61.34) and nuts (61.36), and
check for accurate levelling of the installation with re-
spect to the first foot.
12. Spare parts
When ordering spare parts please quote their designation,
position number in the cross section drawing (
section
14.
) and rated data from the pump name plate (type, date
and serial number).
Any
pumps that require inspection/repair
must
be drained and carefully cleaned inside and
outside before dispatch/submission.
Changes reserved.
Nr.
Designation
13.60 Flange with adapter
14.00 Pump casing
14.02 External jacket
14.04 Plug with washer
14.06 O-ring
14.12 Plug with washer
14.16 O-ring
14.17 Screw
14.18 O-ring
14.19 O-ring
14.20 O-ring
14.42 Plug with washer
14.54 Wear ring (1)
25.01 First stage casing
25.02 Stage casing
25.03 Stage casing with bearing
25.05 Last stage casing
28.00 Impeller
28.04 Impeller nut
28.08 Washer
32.00 Lantern bracket
32.30 Guard
32.31 Washer
32.32 Screw
34.01 Lower cover
34.02 Upper cover
36.00 Mechanical seal
36.51 Retaining ring, split
36.52 Shoulder ring
61.00 Base
61.02 Tie-bolt
61.03 Washer
61.04 Nut
61.07 Screw
61.30 Support foot
61.32 Screw
61.34 Washer
61.36 Nut
64.00 Shaft
64.10 Bearing sleeve
64.13 Upper spacer sleeve
64.14 Lower spacer sleeve
64.15 Spacer sleeve
64.18 bearing spacer sleeve (upper)
64.19 bearing spacer sleeve (lower)
64.22 Coupling
64.25 Screw
66.00 Ball bearing
66.18 Circlip
66.19 Shoulder ring (3)
70.18 Screw
70.19 Nut
99.00 Motor, complete
(1) Inserted in the stage casing
(cannot be supplied separately)
(2) See
section 15.
(3) Only for motor size 132
(2)
(2)
16
Variation 1: suction on the left,
Variation 2: suction on the right,
delivery on the right
delivery on the left
Fig.6 Orientation of the ports in a horizontally-fitted pump
4.93.213/3
4.93.213/4