background image

(OPTIONAL) 

Requirements for UL Compli

a

n

t Installation

UL325 Installation

UL 325 standard is a safety standard for electric gate openers. If 

the gate operator installation 

require

s

 a UL325 installation, 

follow these instructions. For full instructions, visit the UL325 

website.

Class I - Residential Locations

 & Class II - Commercial Locations / Multi-family housing

Slide Gates

:  

Primary Device: 

A

 | 

Secondary Device (one required): B1, B2, D

Swing Gates: Primary Device: A,

 

C  | Secondary Device (one required) A, B1, B2, C, D

Class III - Industrial Locations / Limited Access Vehicular Gates

Slide Gates:  Primary Device: A, B1, B2 |  Secondary Device (one required): A, B1, B2, D, E

Swing Gates: Primary Device: A, B1, B2, C  | Secondary Device (one required) A, B1, B2, D, E

Class IV- Guarded Industrial / Restricted Access Locations

Slide Gates:  Primary Device: A, B1, B2, D |  Secondary Device (one required): A, B1, B2, D, E

Swing Gates: Primary Device: A, B1, B2, C, D  | Secondary Device (one required) A, B1, B2, C, D, E

REQUIRED ENTRAPMENT PROTECTION

A - Inherent (built-in) Entrapment protection System

B1 - Non-contact sensor such as a photo-eye or equivalent

B2 - Contact sensor such as edge sensor or equivalent

C - Inherent adjustable clutch or pressure relief device

D - Actuation device requiring continous pressure to maintain gate motion

E - Inherent Audio Alarm

NOTE

: The same type of device shall not be utilized for both the primary and secondary entrapment 

protection means. Use of a single device to cover both the opening and closing directions is in 

accordance with the requirement; however, a single device is not required to cover both directions.

Class II - Commercial Locations / Multi-family housing

Slide Gates

:  

Primary Device: 

A

 | 

Secondary Device (one required): B1, B2, D

Swing Gates: Primary Device: A,

 

C  | Secondary Device (one required) A, B1, B2, C, D

2

Summary of Contents for CM7-DCFP























Reviews: