background image

CALIFORNIA ACCENT LIGHTING, INC.

2034 E. Lincoln Ave. #431, Anaheim, CA 92806

ph. 800.921.CALI (2254) or 714.535-7900  \  fx. 714.535.7902

[email protected]  \  calilighting.com

© CALI. All rights reserved. CALI reserves the right to make changes or withdraw specifications without prior notice.

Installation Instructions

Overview

lip

LEDs

LLED

8350-UC

2 of 11

WARNING

When using lipLEDs for any application, basic safety precautions 
should always be followed to reduce the risk of fire, electric shock, 
and personal injury. lipLEDs must be installed in accordance with 
the NEC or CEC as applicable.

•  Do not exceed maximum length per circuit. Each maximum run requires  
  additional power feed from the transformer
•  Do not cover lipLEDs as the covering may cause it to overheat, melt, or ignite.
•  Do not install lipLEDs in hazardous locations or closer than 6 inches
  from any curtain or similar combustible material.
•  Do not use lipLEDs if damaged, such as broken outer jacket, loose
  connections, or frayed wire insulation. Inspect periodically. 
•  Do not submerge lipLEDs in liquid.
•  Do not mount lipLEDs with staples, nails, or like means that might
  damage the insulation. Mount with double-sided tape and mounting clips.
•  Do not install lipLEDs in places where it is subject to continuous flexing.
•  Do not mount lipLEDs inside tanks or enclosures of any kind without  
  sufficient ventilation.
•  Ground Fault Circuit Interrupter (GFCI) protections are required 
  on circuits or outlets.
•  Surge protector must be set up for electrical power system to avoid
  damaging lipLEDs lighting system.
•  Do not install in an environment where excessive heat may exist. 
  Ambient temperature -40°F - 122°F (-20°C - 50°C).
•  Only wet location models are intended for outdoors. See package label  
  for environmental details.
•  Do not install wet location model in areas where water will collect.

FEATURES 

*Maximum run is based on 5 Amps: 15’ (8W)
  Maximum run based on 4 Amps: 11’ (8W)

 

APPLICATIONS 

Accent, Decorative Lighting

 VOLTAGE 

24VDC

 

LAMP TYPE 

Color Tuning LEDs

 DIMMING 

DMX-512

 LENGTH 

Built to Order

 MOUNTING 

Mounting Clips or Mounting Channel

 

VIEWING ANGLE 

120 Degrees

 

L70 LED LIFE 

60,000 hrs.

 

MAXIMUM RUN* 

15’ (8W)

 LISTING 

Dry Location

 

  UL2108, CSA C22.2#9

 

  UL8750, CSA250

(Based on 5 amps)

Summary of Contents for lipLEDs LLED8350-UC












Reviews: