background image

4

TO reDuce THe risk Of inJurY:

The water in the spa should never exceed 104°F (40°C). Water temperatures between 100°F (38°C) and 104°F (40°C) are considered safe for a healthy adult. 

• 

Lower water temperatures are recommended for extended use (exceeding ten minutes) and for young children. Extended use can cause hyperthermia.
Pregnant or possibly pregnant women should limit spa water temperatures to 100°F (38°C). Failure to do so may result in permanent injury to your baby.

• 

Do not use spa immediately following strenuous exercise.

• 

aVOIDInG THe rIsk OF skIn Burns:

To reduce the risk of injury, before entering a spa, the user should measure the water temperature since the tolerance of temperature-regulating devices 

• 

varies.
Test the water with your hand before entering the spa to be sure it’s comfortable.

• 

warnInG sIGn

Each Caldera

®

 spa is shipped with a WARNING SIGN in the owner’s package. The sign, which is required as a condition of Product Listing, should be permanently 

installed where it is visible to the users of the spa. To obtain additional SAFETY SIGNS, contact your Caldera dealer and request Part #70798

IMPOrTanT sPa InsTruCTIOns

The following contains important spa information, and we strongly encourage you to read and apply them.

DO:

Use and lock the cover when the spa is not in use, whether it is empty or full.

• 

Follow the Spa Care and Maintenance recommendations stated in this manual.

• 

Use only approved accessories and recommended spa chemicals and cleaners.

• 

DOn’T:

Leave the Caldera spa exposed to the sun without water or the cover in place. Exposure to direct sunlight can cause solar distress of the shell material.

• 

Roll or slide the spa on its side. This will damage the siding.

• 

Lift or drag the vinyl cover by using the cover lock straps; always lift or carry the cover by using the handles.

• 

Attempt to open the electrical control box. There are no user serviceable parts inside. Opening of the control box by the spa owner will void the warranty. If you 

• 

have an operational problem, carefully go through the steps outlined in the Troubleshooting section. If you are not able to resolve the problem, contact your 

authorized Caldera dealer. Many problems can easily be diagnosed over the telephone by an Authorized Service Technician.

saVe THese InsTruCTIOns

sITe PreParaTIOn

You probably have a spot picked out for your new spa, whether it’s indoors or outdoors, on a patio or on a deck. Please make sure you check the following:

Always put your spa on a structurally sound, level surface. A filled spa can weigh a great deal. Make certain that the location you choose can support the 

• 

weight of your filled spa.
Don’t forget to level your spa before filling it. (See the Spa Leveling Preparation section on next page.)

• 

Locate your equipment compartment, which houses all of the electrical components, in a place where water will drain away from it. Allowing water into the 

• 

equipment compartment can damage the electronics, or may result in tripping your house’s circuit breaker.
Leave yourself easy access to the circuit breakers in the subpanel.

• 

Never let water get into the subpanel. Your 230 volt spa’s subpanel is rain-tight when installed correctly with the door closed. Periodically check these 

• 

conditions and correct any flaws if detected.
Leave access to the equipment compartment for periodic spa care and maintenance.

• 

WARNING: Damage to the spa’s equipment compartment components or internal plumbing as a result of rodent infestation is NOT covered under your 

warranty!

OuTDOOr anD PaTIO InsTallaTIOn

No matter where you install your new spa, it’s important that you have a solid foundation to support it. Structural damage to the spa, resulting from incorrect installation, 

or placement on an inadequate foundation, is not covered under the spa’s limited warranty. 
If you install the spa outdoors, we recommend a reinforced concrete pad at least four inches thick. The reinforcing rod or mesh in the pad should be attached to a bond 

wire.  

SAFETY INFORMATION

INSTALLATION

Summary of Contents for paradise series









































Reviews: