23
FIlTer MaInTenanCe
At least once a week, check and clean the skimmer basket and weir to ensure proper
filter flow. Remove leaves, foreign matter, and debris. It is very important to keep your spa
filter cartridge clean and free of particles to ensure proper water flow. A clean filter permits
the hydrotherapy system to function properly and also allows more efficient filter cycles.
Depending on how frequently your spa is used, we recommend cleaning the spa filter
cartridge every four weeks. If this is not done, the filter may clog and restrict water flow, which
causes improper filtration and poor jet performance.
IMPORTANT:
The frequency and duration of use, and the number of occupants all contribute
to determining the appropriate time between filter cleanings. More use means that more
frequent filter cleanings will be required.
FIlTer CarTrIDGe reMOVal anD CleanInG
InsTruCTIOns
Turn off power to the spa.
1.
Push the filter basket down slightly and turn counter-clockwise to unlock. Then pull out
2.
the basket and weir.
Carefully pull up the filter cartridge and bring it out of the spa.
3.
Always clean the filter using a filter degreaser to remove mineral and oil build-up. Soak
4.
the filter in the degreaser (according to the package directions). Then place the filter on
a clean surface and, using a garden hose, spray until it is clean. It may be necessary to
rotate the filter while spraying to remove any debris lodged between the filter pleats.
Replace the cartridge in the spa. To return the basket and weir, insert and rotate
5.
clockwise to lock into position.
Turn on power to the spa.
6.
NOTE:
Replacement filter cartridges are available from your Caldera
®
dealer. Refer to the
back of this manual to determine the appropriate size for your spa.
DIVerTer ValVe MaInTenanCe
If your spa’s diverter valves become difficult to turn, it is likely that sand or grit has become
lodged inside the valve body. It is very important that this debris is removed as soon as possible to avoid damage to the valve. To clean the valves, follow these steps:
Turn off power to the spa.
1.
Remove the diverter valve’s handle by pulling upward while rocking it back and forth.
2.
Unscrew the cap ring.
3.
Remove the valve body by pulling it upward.
4.
Wipe the valve body and the interior walls of the valve clean.
5.
Lubricate the o-rings with a waterproof lubricant available from your Caldera dealer.
6.
Reassemble the valve and turn on power to the spa.
7.
VersassaGe
®
JeTs MaInTenanCe
If the VersaSsage jets spin slower than when the spa was new, or the jets are sticking, it may be due to a build-up of deposits inside the jet bearings. To remove the
deposits, follow these instructions:
With the spa off, rotate the VersaSsage jet face counter-clockwise until it stops.
1.
Once the face stops rotating, use a little extra force to rotate the face counter-clockwise past the locking position until it stops. Pull the face away from the spa.
2.
After flushing the bearings inside the body with water, spin the rotating nozzle. It should spin freely. If it does not, place the bearing end in a cup of vinegar (the
3.
vinegar will soften any deposits). Let it soak overnight. The next day, flush with water and repeat the spin test.
NOTE
: If it still doesn’t spin freely, then a second night of soaking is required. Replace the jet if the bearing still does not spin.
To replace, position the face body downward and push the face body back into the jet fitting. Slightly rotate face body in either direction until you feel the body align
4.
with the fitting, and then press firmly on the face. Once seated, rotate the face clockwise using a little extra force to overcome the locking position. If the face does
not rotate, remove and rotate the face 180°, and repeat this step.
Turn the jet pump on. The VersaSsage jet should spin freely.
5.
MAINTENANCE
FLOATING WEIR
BASKET
FILTER
CARTRIDGE
STANDPIPE
PLEATS
Summary of Contents for paradise series
Page 1: ......
