Cabletron Systems 9A600 Configuration Manual Download | Manualshive

Page: 115 / 158

background image

9A656-04 and 9A600 Configuration Guide

4-1

CHAPTER 4

SIGNALLING AND ROUTING

This chapter discusses the Signalling protocols supported by the SmartSwitch 9500, and
provides details on default settings and configuration options. In addition, this chapter
provides instructions on manually configuring the Signalling stacks and creating static routes
using MIBs. To perform these tasks, a NMS that provides support for the AToM MIB and the
PNNI MIB is a requirement. Refer to

Appendix C

for more information on the MIB support

for the 9A656-04.

This chapter is divided into the following three subsections:

•

Persistence (

Section 4.1

)

•

Signalling (

Section 4.2

)

•

Routing (

Section 4.3

)

4.1

PERSISTENCE

There are several procedures described in this chapter that, when executed, create permanent
configurations for the interface on which they were performed. These configurable options are
performed on an interface by interface basis via the AToM MIB (for UNI and IISP
configuration) and the PNNI MIB (for IISP and PNNI configuration). Before performing any
of these configurations, be aware that the only way to revert these settings to the factory
default settings is to clear NVRAM. Instructions on how to clear NVRAM can be found in the
9A656-04 or 9A600 Hardware and Installation Guide. Pressing the RESET button on the
front of the module will NOT restore factory default settings after they have been changed.

NOTE

The figures in this chapter use examples of the Cabletron Systems Spectrum MIB
Tools utility. Other SNMP applications will have a different appearance, but will allow
the user to perform the same tasks.

All references to the CTM backplane or CTM interfaces apply ONLY to the
9A656-04 ATM SmartSwitch module, as the 9A600 does not connect to the CTM
backplane.

«
...
113
114
115
116
117
...
»

Summary of Contents for 9A600































































































































































Reviews:

No comments

Related manuals for 9A600

Brand: ABB Pages: 138

Brand: ABB Pages: 116

Relion 615 series

Brand: ABB Pages: 136

Brand: wattio Pages: 20

Brand: IFM Pages: 49

Smart Control Panel 880RGD

Brand: Raynor Pages: 4

Brand: GEA Pages: 13

Brand: Nice Pages: 32

Dual Motor Focus Controller

Brand: Pegasus Astro Pages: 16

Brand: Jeckson Electric Pages: 2

Brand: J+J Pages: 6

Brand: DNF Controls Pages: 22

Brand: Matelec Pages: 2

Brand: NDS Pages: 20

EXTA LIFE P-520

Brand: Zamel Pages: 10

SatService sat-nms VLC

Brand: Calian Pages: 40

Brand: Jetter Pages: 24

lyriQ AU7394 Series

Brand: On-Q Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands