background image

8

9

English

JUST SPEAK S

JUST SPEAK S

Low Battery Warning

When the battery is low, the blinking blue LED in stand-by mode turns to 
red and you will hear mid-tone triple beeps and a voice prompt saying “

Low 

battery

”.

Adjusting the Volume Level

You can easily adjust the volume by pressing the (+) Button or the (-) Button. 
You will hear a beep when the volume reaches maximum or minimum level. 
The volume is set and maintained independently at different levels for each 
audio source even when you turn off and on the headset. For example, 
once you set the volume for mobile phone handsfree, it will not change even 
if you adjust the volume when you hear Bluetooth MP3 music. So you can 
always maintain the preferred optimum volume level for each audio source.

Function Priority

The Just Speak S operates in the following order of priority:  

(Highest)

 

Mobile Phone

 

Intercom

(Lowest)

 

Bluetooth Stereo Music  

A lower priority function is always interrupted by a higher priority function. 
For example, stereo music is interrupted by an intercom call, and intercom 
conversation is interrupted by an incoming mobile phone call.

Fault Reset

When the Just Speak S is not working properly or is in faulty status for 
any reason, you may reset by pushing the pin-hole reset button on the left 
speaker unit. Insert a paper clip into the reset pin-hole and press and hold 
the reset button for a second with light pressure. The Just Speak S will be 
switched off after which time, you have to turn the system back on and try 
again. However, this will not restore the headset to factory default settings.

4. 

OPERATION QUICK REFERENCE

Function

Operations 

Power 

On/Off

1 sec.

1 sec.

+

Volume 

Adjustment 

1 press

1 press

or

Intercom 

Pairing

pairing

A

B

1)

5 sec.

5 sec.

2)

1 sec.

4. OPERATION QUICK REFERENCE

Function

Operations 

Bluetooth 

Pairing

(Phone, MP3, 

GPS)

1)

Sena SMH3

Caberg JSS v1.0

5 sec.

2)

Sena SMH3

Caberg JSS v1.0

Select 

Caberg Just Speak S

3)

Sena SMH3

Caberg JSS v1.0

Enter

PIN

Start & End 

Intercom 

Conversation

1 sec.

Configuration

10 sec.

Summary of Contents for Just SpeakS















Reviews: