background image

34

35

Service Functions

6.1 

Firmware Update from Storage Device

i

Notice!
The firmware file can be obtained from the internet.

Access only with storage device defined as 

Default storage

 !

1.  Select 

Setup > Interfaces 

>  

Default Storage >

  

USB Memory

 

 "4.1.4" on page 16.

2.  Format USB flash drive in the printer 

 "9.5.3" on page 44.

The directories "fonts", "images", "labels" and "misc" are created on the storage device here.

3.  Copy the firmware file to the "misc" directory of the storage device. This can be done on a computer or via FTP on 

the printer.

4.  Insert the prepared storage device into the printer.
5.  Start Offline menu.
6.  Select 

Service.

If the menu is protected via a PIN a prompt appears in the display. Enter the code number and confirm with 

OK

.

7.  Select 

Firmware fr. storage device

.

The names of the firmware files found on the storage device are shown in the display.

8.  Select the desired file an confirm with 

The selected firmware file is copied. A progress indicator is displayed while the firmware is being copied. After 

completion the printer will be re-started. 

i

Notice!
The firmware update also can be done via FTP printer management 

 "8.4" on page 41.

6.2 

Load Settings

Access only with storage device defined as 

Default storage

 !

A printer configuration previously saved to a storage device (USB flash drive, Internal Flash File System) can be 

loaded with the 

Load settings

 function.

1.  If the printer configuration was saved to an USB flash drive, select 

USB Memory

 as 

Default Storage 

and  

insert USB flash drive into an USB master interface. 

If the printer configuration was saved on the Internal Flash File System, select 

IFFS 

as 

Default Storage

.

2.  Start Offline menu.
3.  Select 

Service

.

If the menu is protected via a PIN a prompt appears in the display. Enter the code number and confirm with 

OK

.

4.  Select 

Load settings

.

5.  Select the desired file.
6.  Confirm with 

.

Loading of the configuration data starts. Do not remove the USB flash drive until the loading procedure is 

complete. The printer returns to the 

Service 

menu.

If an error occurs during the loading procedure, an error message appears in the display. Restart the loading 

procedure in this case. If an error occurs again, the configuration parameters must be entered via the control panel.

Summary of Contents for EOS4

















































Reviews: