background image

10  

 

Due to our policy of continual product improvement CP Electronics reserves the right to alter the specification of this product without prior notice. 

Dimensions 

See diagrams opposite. 

Weight 

0.10kg 

Supply Voltage 

/- 10%, /- 10%  

Frequency 

50/60Hz 

Circuit protection 

10A 

Dimming output 

Basic insulation only. Although low voltage, 
this is not an SELV output and should be 
treated as if mains potential. Use mains 
rated wiring. 

Maximum Switching Load 

2 Amps fluorescent and incandescent 
lighting. 
2 Amps compact fluorescent lighting. 
2 Amps low energy lighting. 
2 Amps low voltage lighting (switch primary 
of transformer). 
Switch SON lighting loads via a contactor.  

Number of ballasts  

Up to 4 dimming ballasts. 

Power consumption 

PRM 

On 307mW, Off 228mW 

DD 

On 357mW, Off 228mW 

AD 

On 344mW, Off 268mW 

Cable specification 

1m,  silicon insulation and sheath.

 

 

PRM 

3 x 0.75mm

2

 

 

AD & DD 3 x 0.75mm

2

 & 2 x 0.50mm

2

 

 
Temperature 

-10ºC to 50ºC 

Humidity 

5 to 95% non-condensing 

Material 

Flame retardant ABS/PC 

 

Type 

Class 2 

IP rating 

IP40 

 
Compliance 

EMC-2004/108/EC 
LVD-2006/95/EC 

Technical data 

Part numbers 

C.P. Electronics Ltd

 

Brent Crescent 
London 
NW10 7XR 
United Kingdom 
Tel: 

+ 44 (0) 333 900 0671 

Fax: 

+ 44 (0) 333 900 0674 

www.cpelectronics.co.uk 
[email protected] 

Ref:  #WD676    Issue 2 

IMPORTANT NOTICE! 

This device should be installed by a qualified electrician in 
accordance with the latest edition of the IEE Wiring 
Regulations and any applicable Building Regulations. 

 

Part number 

Description 

Detectors 

EBMINT-AD 

Integrated PIR detector AD 1-10V 

 

EBMINT-DD 

Integrated PIR detector DD DALI/DSI 

 

EBMINT-PRM 

Integrated PIR detector PRM 

Accessories 

UHS5 

Programming IR handset 

 

UNLCDHS 

Universal LCD IR handset 

UK patent GB2498572 and international patents applied for

.

 

Summary of Contents for EBMINT











Reviews: