background image

_

 3 

_

Fuel safety

1.  Petrol is highly flammable and must be handled and stored carefully. Use a container approved for 

fuel for storing petrol and/or fuel/oil mixture.

2. Mix and pour fuel outdoors and where there are no sparks or flames.

3. Do not smoke near fuel or Multi-cutter, or while using the Multi-cutter.

4. Do not overfill the fuel tank. Stop filling 10mm from the top of the tank.

5. Wipe up any spilled fuel before starting the engine.

6. Move the Multi-cutter at least 3m (10ft.) away from the fueling location before starting the engine.

7. Do not remove the Multi-cutter fuel tank cap immediately after stopping the engine.

8. Allow the engine to cool before refueling.

9. Drain the tank and run the engine dry before storing the unit.

10.  Store fuel and Multi-cutter away from open flame, sparks and excessive heat. Make sure fuel vapors 

cannot reach sparks or open flames from water heaters, furnaces, electric motors, etc.

Multi-cutter Operating safety

1.  THIS MULTI-CUTTER CAN CAUSE SERIOUS INJURIES. Read the instructions carefully. Be famil-

iar with all controls and the proper use of the Multi-cutter.

2.  Never allow children to operate the Multi-cutter. It is not a toy. Never allow adults to operate the unit   

without first reading this Operator’s Manual.

3.  Avoid using the Multi-cutter near rocks, gravel, stones and similar material that would cause harmful 

missiles.

4.  Keep children, bystanders and animals outside a 15m (50ft.) 

radius from the operator and Multi-cutter.

5.  If you are approached while operating the Multi-cutter, stop the 

engine and attached tool moving.

6. Use the Multi-cutter only in daylight or good artificial light.

7. Never operate the Multi-cutter without proper guards in place.

8.  Do not put hands or feet near or under any moving parts. Keep clear at all times. Keep all parts of 

your body away from the moving tool attachment and hot surfaces such as the muffler.

9. Keep a firm footing and balance. Do not overreach.

10.  Use the right tool for the job. Do not use the Multi-cutter for any job that is not recommended by 

BUSHRANGER.

15m (50ft.)

Minimum

Summary of Contents for MCH252













Reviews: