background image

 LOG SPLITTER

13

Hold the lifting handle and slowly lower the 
beam. It  will  lock  automatically. Double 
check  to  make  sure  the  beam  bracket  is 
locked onto the beam.

2.

Do not let the beam suddenly drop. 
Keep  hands  and  fingers  clear  of 
pinch or crush points at all times.

MANUAL TUBE

LOG CRADLES

Remove  the  cap  from  the  manual  tube. 
Align  the  holes  in  the  manual  tube  with 
the holes in the tow bar. Insert and tighten 
bolts and washers. (See 

Figure 8

)

Reattach the cap.

1.

2.

M12x35

 (x8)

Log Cradle (Right)

Outside Holes

Inside Holes

Figure 9

16

mm

13

mm

18

 

mm

19

mm

30

 mm

32

mm

32

mm

13

mm

16

mm

19

 

mm

Beam Lock Bracket

Figure 7b

M8x20

 

(x2)

Manual Tube

Cap

16

mm

13

 

mm

18

mm

19

mm

30

 mm

32

mm

Figure 8

2.  Follow step 1 to assemble the left log cradle.

(See 

Figure 9

)

1.  Align the holes on the right log cradle to the

inside and lower holes on the beam mounts.
Insert  the  M12x35  bolts, 

flat

  washers,  and

nuts and securely tighten.

M12 X 35

X 8

G

M8 X 20

X 2

F

LOG TABLE (OPTIONAL)

Refer  to 

Figures 9

  and 

10

  to  install  the  work 

table. Remove the bolts, flat washers, and nuts 

from  the  inside  holes.  Move  the  log  cradle 
from  the  incline  position  to  the  horizontal 
position.  Align  the  holes  on  the  log  cradle 
with  the  outside  holes  on  the  beam  mount. 

Reinstall the bolts, flat washers, and nuts.

Place the work table over the holes in the log 
cradle  and  align  the  4  holes  from  the  work 
table  plate  and  log  cradle.  Insert  and  tighten 
the M10x25 bolts, spring washers, 

flat

 washers, 

and nuts.

M10x25 

(x4)

Work Table

Outside Holes

Log Cradle (Right)

Inside Holes

M10 X 25

X 4

8

16

 mm

13

mm

18

mm

19

mm

30

 mm

32

mm

Figure 10

Summary of Contents for LS301





























Reviews: