background image

 LOG SPLITTER

21

STORAGE

WARRANTY

Never  spray  the  engine  or  log 
splitter  with  a  pressure  washer. 
Water  can  contaminate  the  fuel 
system and can enter the engine 
and damage the engine.

Follow the instructions below for storing your 
log splitter between uses.

Retract the wedge completely to keep the 
rod protected from corrosion.

Allow the machine to cool 5 minutes before 
storing.

Refer  to  the  engine  manual  for  proper 
engine storage instructions.

Clear  the  debris  from  the  beam,  wedge, 
and  end  plate.  Use  a  damp  cloth  to  clear 
exterior  surfaces  of  the  engine  and  log 
splitter. Use a soft bristle brush to remove 
excess dirt and oil. Use an air compressor 
(25 PSI) to clear dirt and small debris. Wipe 
the beam, wedge, and all metal parts with 
an oil rag to prevent corrosion. 

1.

2.

4.

3.

  can  become  stale  when 

stored  over  30  days.  Stale  fuel 
can  cause  acid  and  gum  deposits 
that  form  in  the  fuel  system  or  on 
carburetor  parts.  For  engine  fuel 
that  is  stored  less  than  30  days, 
add  a  fuel  stabili

s

er  to  keep  the 

fuel  fresh.  Turn  the  fuel  valve  lever 
to  the  off  position.  If  fuel  is  stored 
over  30  days,  then  drain  the 
fuel  tank  as  stated  in  the  engine 
manual.

Always drain fuel from the tank in 
an outdoor, well-ventilated area.

Stay away from sources of heat, 
flame  or  sparks  while  handling 
fuel.

Clean up fuel spills immediately.

Never store the log splitter inside 
where  there  is  a  source  of  heat 
or an open flame, spark, or pilot 
light,  such  as  a  water  heater, 
space  heater,  furnace,  clothes 
dryer,  or  other    appliance. 
EVEN IF the log splitter's fuel tank 
is  empty,  residual 

 

vapors 

could ignite.
Never store the log splitter near 
fertili

s

er  or  any  other  corrosive 

material.

  vapors  can  ignite  if  they 

collect  inside  an  enclosure 
and  explosion can result.

Store 

petrol

  in  a  cool,  dry  place  in  a 

tightly sealed container.

Store  the  log  splitter  in  a  location  away 
from  corrosive  materials,  sources  of  heat, 

open flames, sparks, or pilot lights.

6.

5.

3 years domestic warranty (excludes engine and 
hydraulic components). 1 year hydraulic components. 
Engine as per engine manufacturer’s warranty.

This warranty does not extend to: 
•  Replacement of parts due to fair wear and tear 
 

over time.

•  Damage caused by the purchaser such as failure to  
 

maintain, operate, fuel or store the goods according  

 

to the procedures specified in the owner`s manual  

 

and abnormal use of the goods.

•  Failure or damage caused by the modifications or  

 

alterations to the goods which change their  

 

 

intended use or adversely affect their performance,  

 

safety, operation or durability.

To be entitled to claim on this warranty the purchaser 
must report the fault of defect to an authorised 
Bushranger

TM

 dealer and provide proof of purchase 

within the relevant warranty period specified.

AUSTRALIAN CONSUMER LAW (REG. 90):

The  benefits  to  the  consumer  given  by  this  warranty 

are in addition to other rights and remedies of the 
Consumer under a law in relation to the goods or 
services to which this warranty relates.

Our goods come with guarantees that cannot be 
excluded under the Australian Consumer Law. You are 
entitled to a replacement or refund for a major failure 
and for compensation for any other reasonably 
foreseeable loss or damage. You are also entitled to 
have the goods repaired or replaced if the goods fail to 
be of acceptable quality and the failure does not 
amount to a major failure.

The text above applies notwithstanding anything else 
expressed or implied to the contrary in this warranty 
document.

Summary of Contents for LS301





























Reviews: