background image

Spare Parts Kits

Note

: When ordering spare parts or accessories acc. to the table below

please always quote the type (“Type”) and the serial no. (“No”) of the
vacuum pump. This will allow Busch service to check if the vacuum
pump is compatible with a modified or improved part.

The exclusive use of genuine spare parts and consumables is a pre-
requisite for the proper function of the vacuum pump and for the
granting of warranty, guarantee or goodwill.

This parts list applies to a typical configuration of the vacuum pump
RB/RC 0006 C/E. Depending on the specific order deviating parts data
may apply.

Your point of contact for service and spare parts in the United
Kingdom:

Busch (UK) Ltd.
Hortonwood 30-35
Telford
Shropshire
TF1 7YB
Tel:

01952 677 432

Fax:

01952 677 423

Your point of contact for service and spare parts in Ireland:

Busch Ireland Ltd.
A10-11 Howth Junction Business Centre
Kilbarrack, Dublin 5
Tel:

+353 (0)1 8321466

Fax:

+353 (0)1 8321470

Your point of contact for service and spare parts in the USA:

Busch lnc.
516-B Viking Drive
Virginia Beach, VA 23452
Tel:

1-800-USA-PUMP (872-7867)

Your point of contact for service and spare parts in Canada:

Busch Vacuum Technics Inc.
1740, Boulevard Lionel Bertrand
Boisbriand (Montréal)
Québec J7H 1N7
Tel:

450 435 6899

Fax:

450 430 5132

Your point of contact for service and spare parts in Australia:

Busch Australia Pty. Ltd.
30 Lakeside Drive
Broadmeadows, Vic. 3047
Tel:

(03) 93 55 06 00

Fax:

(03) 93 55 06 99

Your point of contact for service and spare parts in New Zealand:

Busch New Zealand Ltd.
Unit D, Arrenway Drive
Albany, Auckland 1311
P O Box 302696
North Harbour, Auckland 1330
Tel:

 

0-9-414 7782

Fax:

 

0-9-414 7783

Find the list of Busch companies all over the world (by the time of the

 

publication of these installation and operating instructions) on

page

 

19

 

(rear cover page).

Find the up-to-date list of Busch companies and agencies all over the

 

world on the internet at

 

www.buschvacuum.com

.

Spare parts kit

Description

Part no.

Service kit

consisting of exhaust

filter and pertinent seals

0992 000 001

Set of

seals/gaskets

consisting of all necessary

seals

0990 000 031

Overhaul kit

consisting of seal set and

all wearing parts

0993 000 051

Accessories

Accessories

Description

Part no.

Air filter

inlet-side, with paper

cartridge, to separate

solids

0945 000 108

Replacement paper

cartridge

0532 000 033

Oil

Denomination

VM 032

VM 068

ISO-VG

32

68

Base

Mineral oil

Mineral oil

Density [g/cm³]

0.872

0.884

Ambient temperature range

[°C]

12 … 30

12 … 30

Kinematic viscosity at 40 °C

[mm²/s]

30

68

Kinematic viscosity at 100 °C

[mm²/s]

5

8.5

Flashpoint [°C]

225

235

Pourpoint [°C]

–15

–15

Part number 0.1 l packaging

0946 000 942

Part number 1 l packaging

0831 000 086

0831 102 492

Part number 5 l packaging

0831 000 087

0831 102 493

Filling quantity, approx. [l]

RB 0006 C: 0.1

RB 0006 E: 0.2

RB/RC 0006 C/E

Spare Parts Kits

0870152229

page 17

Summary of Contents for R5 RB 0006 C






















Reviews: