background image

 

 

 

 

burster Italia s.r.l. · 

· 

· 

· Sede legale ed operativa · 

· 

· 

· Via Cesare Battisti, 16/18 · 24035 Curno (BG) · Tel. +39 035 618120 · Fax +39 035 618250 

e-mail: [email protected] · http://www.burster.it 

C.F. e P.IVA 11048400151 · Capitale sociale Euro 49.920,00 ···· R.E.A. di Bergamo 276749 

 

 

 
 
 

Apparecchi di misura di precisione. Sensori e Sistemi 

per grandezze elettriche, termiche e meccaniche 

 

Imprint 

 

Valid for...  

86-2113; 86-2413; 86-2493;  

86-2153; 86-2453; 86-2494 

and similar. 

Reprint-Interdiction   Reprint, even in extracts, only with written authorization.  

Modification  

Technical changes reserved. 

 

References in this Text 

1.6 Warning Notes; Page 5 

 

Attention must be paid to the accident prevention regulations of the trade associations. 
Coverings  and  casings  are  necessary  before  operating  the  sensor.  This  is  also  valid  for 
commissioning, maintenance and trouble shooting. 
Duties of the coverings and casings are: 

  Protection from detaching parts 

  Protection from contusion and shear 

  Prevention from reaching rotating parts 

  Prevention from being tangled up and/or getting caught by parts 

Coverings may 

  Not grind 

  Not rotate  

Coverings are also necessary outside of operating and motion travel areas of persons. 
These  demands  can  be  modified  if  other  sufficient  safety  devices  are  available.  During 
operation,  the  safety  precautions  must  be  operative.  By  vibrations,  damages  can  occur  at 
hand-guided devices which can lead to injuries.   

 

4 Mechanical Assembly; Page 7 

 

Caution:  During  the  assembly  inadmissibly  large  forces  may  not  act  on  the  sensor  or  the 
couplings.  

 

During the assembly the sensor must be supported to protect it from falling down. 

4.1 Typical Application; Page 8 

 

Caution: Do not use pulse or impact wrenches!! 

6.1 Engaging; Page 10 

 

Warming-up period of the torque sensor is approx. 5 min. 

6.4.2 Natural Resonances; Page 11 

 

An operation of the device in natural resonance can lead to permanent damages. 

Summary of Contents for 86-2113














Reviews: