background image

TECHNICAL PASSPORT. INSTALLATION and OPERATION MANUAL

TECHNICAL PASSPORT. INSTALLATION and OPERATION MANUAL

4

1. EXPLANATION OF SYMBOLS AND 

SAFETY INSTRUCTIONS

1.

1. 

Explanation of symbols

CAUTION!

 - 

Important 

recommendation  or  warning 

concerning  safety  conditions  during 

installation  and  operation  of  the  pellet 

burner

DANGER! 

fault  or  improper  use 

may cause injury or be hazardous 

to life of humans or animals.

FIRE HAZARD!

 - 

fault or improper 

installation  and  operation  may 

cause fire.

INFORMATION

 - 

Important 

information  on  the  proper 

operation of the product.

1.2. 

Requirements  to  pellet  burner 

installation room

This manual contains important 

information  for  the  safe  and  correct 

installation,  start-up  and  trouble-free 

operation and maintenance of the pellet 

burner.
The pellet burner can be used for heating 

rooms only in the manner described in 

this manual.
The  application  and  any  other  was  the 

area of operation is not recommended by 

the manufacturer and is not responsible 

for the occurrence of defects or failures.
Note the pellet burner type data 

indicated on the factory rating label and 

the technical data provided in chapter 12 

in  order  to  ensure  proper  operation  of 

the product.

1.2.1.  Instructions to boiler installer

During  installation  and  operation,  the 

country-specific 

requirements and 

regulations must be observed:

• local  construction  regulations  on 

installation,  air  supply  and  exhaust 

gas  extraction  as  well  as  chimney 

connection.

• regulations and norms concerning the 

fitting  of  the  heating  installation  with 

safety devices.

i

Use only original BURNiT parts

WARNING!  Installation  and 

setting the pellet burner should 

be  done  by  an  authorized 

specialist / service shop and must 

follow  the  safety  instructions 

and rules of operation.

DANGER of intoxication, 

suffocation.

Inadequate  inflow  of  fresh  air 

to the boiler room may result in 

dangerous leak of exhaust gases 

during burner operation.

- Make  sure  the  air  inlets  and 

exhaust  gas  outlets  are  not 

clogged or closed.

- If  faults  are  not  remedied 

immediately,  the  burner  must 

not be operated

- The user must be provided with 

written instructions on the fault 

and the hazard it entails.

It  is  mandatory  to  assure  a 

backup  power  generator  of 

corresponding  rated  power! 

(see 12.3)

!

DANGER  of  fire  when  burning 

flammable materials or liquids.

- Flammable 

materials/liquids 

must  not  be  left  in  close 

proximity  of  the  burner  and 

heating boiler. 

- Instruct  system  user  of  the 

allowed  minimum  clearances 

from surrounding objects.

Summary of Contents for Pell 150





































Reviews: