Burndy PATMD430LWJAW Safety Operating & Maintenance Instructions Download Page 18

18

LITHIUM ION (Li-ion) SHIPPING REGULATIONS

:

The U.S. DOT enacted new regulations in 2008 that 

apply to shipments containing Lithium ion batteries. 

Whenever possible, Lithium ion batteries should be 

sorted from other rechargeable batteries. 

Shipment of a non-Call2Recycle container of Lithium 

ion batteries for recycling must adhere to the following 

requirements, in addition to the safety requirements 

listed on the opposite side: 

· 

Each individual rechargeable battery, or cell 

phone with battery, must be placed into a 

separate bag (or terminals taped) to ensure 

safe storage and shipping; 

·

  Package must be marked “CONTAINS 

LITHIUM ION BATTERIES – FORBIDDEN 

FOR TRANSPORT ABOARD AIRCRAFT AND 

VESSEL.” Lettering must be at least 0.25 

inches in height; 

·

  Package also must be marked: “DO NOT 

DAMAGE OR MISHANDLE PACKAGE – IF 

PACKAGE IS DAMAGED, BATTERIES MUST 

BE QUARANTINED, INSPECTED AND 

REPACKAGED”; 

·

  Shipping document (e.g., BOL) must indicate 

package contains lithium batteries and 

package must be quarantined, inspected and 

repackaged if damaged; and 

·

  Package may not exceed 30 kg (66 pounds)

• Used batteries may have a significant residual charge.  It 

is important that they are prevented form short-circuiting.  

This can be done by placing the batteries separately in 

plastic bags or by placing non-conductive tape over the 

battery terminals.

•  While these batteries are normally safe to handle, they do 

contain caustic materials that may have "vented" due to 

misuse during the life of the battery.  If the battery appears 

to be "dirty" or have a white "film-like" substance around 

the terminal, exercise caution when handling the battery.  

Do not touch the dirty area.  Wash your hands with soap 

and water if they feel itchy, and avoid touching your eyes, 

nose, mouth.

•  Do not attempt to discharge the battery by short-circuiting 

the terminals,  consult your battery supplier for proper 

instructions on discharging batteries.

• Do not bite, or place the battery in your mouth or nose.
• Do not place wet batteries in a plastic bag.  The trapped 

moisture will cause the battery to rust.

SAFETY GUIDELINES FOR BATTERY COLLECTION

LITHIUM ION BATTERIES

When recycling batteries you must include a bill of lading 

in order to comply with all applicable state and federal 

requirements, or the recycling center may be forced to 

return the shipment at your expense.  If you have any 

questions, please contact the recycling center directly.

The EPA certified RBRC Recycling Seal indicates 

BURNDY

®

   is voluntarily participating in a program to 

recycle these batteries at the end of their useful life.  The 

RBRC program provides a convenient 

alternative to placing batteries into the 

trash, which may be illegal in your area.  

Please call 1-800-822-8837 for more 

information.  BURNDY

®

   is committed 

to preserving our environment and 

conserving natural resources.

Approved Battery Recycling Location:

BURNDY

®

 encourages recycling of its products whenever 

feasible. Recycling regulations and methods vary within 

North America and BURNDY

®

 does not endorse any one 

recycling method or company. Consumers that wish to 

recycle BURNDY

®

 products in North America are asked to 

do so according to your local, state and federal regulations. 

Recycling resources for the United States can be found at 

the US EPA web site at the following link: 

http://www.epa.gov/recycle

If you wish to recycle batteries please use the above 

link and/or contact your local RBRC recycling center. 

If additional information is needed please contact the 

BURNDY

®

, Littleton Tool Service Center

A package containing Lithium ion batteries with a gross 

weight of more than 30 kg (66 pounds) must be shipped 

as a fully-regulated Class 9 hazardous material and 

marked "LITHIUM BATTERY, UN 3090" and carry the 

Class 9 Miscellaneous hazard label. Batteries must be 

protected from short circuits and placed in strong outer 

packaging or UN specification packaging. Shipments also 

must be accompanied by hazardous materials shipping 

paper. Shippers must be trained in accordance with the 

U.S. hazardous materials regulations.

Summary of Contents for PATMD430LWJAW





















Reviews: