6
•
Once located over the screws push
the eject chute down firmly to
ensure it is locked in place.
Bread feed chute
WARNING: Ensure your toaster
is disconnected at the mains power
supply and has cooled down before
adjusting the bread feed chute.
Bread feed chute is designed to
enable toast to be automatically feed
into the toaster. Using the bread feed
chute will ensure the most efficient
and even toasting possible is achieved.
•
The bread feed chute will already
be attached to your toaster.
•
To use, ensure that the chute is
protruding from the front of the
toaster.
•
Whilst not in use or for storage the
toast feed chute can be rotated
back and stored on the top of
your toaster.
Toasting
Products for toasting when placed
on the conveyor belt pass through the
cooking area which has elements both
above and below. Items of different
thickness, sizes, moisture and sugar
content will toast at different speeds.
However, the main derminant of the
final result is the conveyor speed which
can be adjusted using the selection
dial.
IMPORTANT: The toasting of
coated or buttered products such as
cheese sandwiches or garlic bread is
not recommended. Any residue from
these items if deposited inside the
toaster could ignite or inhibit the
performance of your toaster.
Use
IMPORTANT: On first use ensure all
packaging and holding tapes are
removed from the unit.
•
Plug the unit into a properly
grounded electricity supply.
•
Suggested the unit is allowed to
heat up fully on the initial
operation as it is likely to give off
a new smell initially.
Warm up / single or
double sided toast
•
Select single or double sided
toasting.
•
The dial on the right of the
control panel (element selection
dial) allows you to select whether
you require:
Single sided toasting (top
element only active)
Double sided toasting (both
elements active)
•
The green power indicator will
illuminate and will remain
illuminated whilst there is power
to the unit.
IMPORTANT: It is recommended that
20 minutes is allowed for your
toaster to warm up before use for
economy mode.
Make toasting and
shade selection
•
The dial on the left of the control
panel (shade selection /speed
control) allows you to select the
5
shade of toasting required (this is
achieved by adjusting the speed
of the conveyor belt.)
•
To change the shade of toasting
you require select from the
following:
Very light
toasting
Medium
toasting
Very dark
toasting.
Tip: It is suggested that to achieve
desired level of toasting the
toaster should be set to “Medium
toasting’ on first use. Insert a
piece of toast to test level, when
this is dispensed adjust controls
accordingly to achieve desired
result. The control cover panel can
then be attached to prevent
changing of settings (see below)
•
During use the shade selection and
element selection dials can be
adjusted as required.
Additional
features
Control panel cover
WARNING: Ensure your toaster has
cooled down before attaching
or removing control panel cover.
•
Ensure the fixture beneath of the
control panel cover is extended.
•
Place control panel cover over the
control panel.
•
Push against unit and turn fixture
anti-clockwise until the cover is
secure.
Economy mode
This feature allows the toaster to be
put into standby mode, which
reduces the power economy mode
by 50%.
•
To activate select the ‘Econ’ on
the using the
element selection
dial on the right
of the control
panel.
•
To revert back
to full operation
select single or double sided
toasting as above. Allow a
minimum of 2-3 minutes before
toasting: the unit will be back up
to full temperature within 10
minutes.
Cleaning
WARNING: Always disconnect the
plug from the mains and allow
to cool before cleaning.
•
Remove crumb tray and chutes to
clean. These items are both
dishwasher safe, or they can be
cleaned using a cloth and small
amount of non-abrasive cleaner.
•
Wipe the outside of your toaster
with damp cloth. It is
recommended that this is done
daily. Stubborn stains may be
removed using a good stainless
steel cleaner or non-abrasive
cleaner.
•
Hard to reach areas should be
cleaned using a small bristle brush
and mild cleaner.
IMPORTANT:Do not use abrasive
cleaners on the toaster as this
could scratch the finish of your
toaster.
O ff
E
c
o
n
77010 rev2:77010 rev3
15/10/08
10:49
Page 9
