background image

4

IMPORTANT SAFEGUARDS

Follow these basic safety precautions when using electrical appliances 

to reduce the risk of fire, electric shock, and/or personal injury:

•  Read all instructions.

•  Do not touch hot surfaces. Use handles or 

knobs.

•  To protect against electric shock, do not 

place cord, plug, or brewer in water or 

liquid.

•  Close supervision is necessary when the 

brewer is used by or near children.

•  Unplug from outlet when not in use for 

extended periods of time and before 

cleaning.  Allow to cool before putting on 

or taking off parts, and before cleaning.

•  Do not operate the brewer with a 

damaged cord or plug, or after the brewer 

malfunctions or has been damaged 

in any manner. Return the brewer 

to an Authorized Service Facility for 

examination, adjustment, or repair. (Refer 

to page

 

25)

•  The use of an accessory not evaluated for 

use with this brewer may cause injuries 

and is not authorized.

•  For indoor use only. Do not use outdoors.

•  Do not let the power cord hang over edge 

of table or counter, or touch hot surfaces.

•  Do not place the brewer on or near a hot 

gas or electric burner, or in a heated oven.

•  Do not use brewer for other than its 

intended use.

•  Do not insert or remove pod holder while 

brewing. Press the coffee or tea button to 

stop or cancel a brew cycle.

•  A canceled brew cycle is not held in 

memory. The next brew cycle will 

dispense full volume based on the volume 

setting.

•  To avoid container overflow, empty mug 

before each brew cycle.

•  Never place hands directly under the 

pod holder. Hot water and steam can be 

present.

•  Do not place brewer in a sink or near 

other water source. Remove reservoir and 

fill separately or use the slide lid.

•  When the brewer is idle, the lid should be 

in the closed position.

•  Always use a mug or bowl that is larger 

than the brew volume selected.

•  Keep hands away if container overflows. 

Wait until brew finishes, let liquid cool, 

then lower volume setting or use a larger 

mug.

•  Never brew without the pod holder insert 

in place. Excessive pressure on the pod 

could result in coffee or tea escaping 

from the holder and into the container. 

Hot liquid splash and burns could occur.

•  Use cold water only.

•  Do not place torn pods or use ground 

coffee in pod holder.

SAVE THESE INSTRUCTIONS

•  A short power-supply cord is used to reduce the risks resulting from becoming entangled 

in or tripping over a longer cord.

•  If an extension cord is used, the marked electrical rating of the extension cord should be 

at least as great as the electrical rating of the brewer, and the cord should be arranged 

so that it will not hang over the edge of the table or counter where it can be pulled on by 

children or tripped over.

•  The extension cord must be of the 3-pronged, 3-socketed, grounding  type, 3-wire cord. 

(Including  grounding conductor).

•  If the power cord is ever damaged, it must be replaced by the manufacturer or authorized 

service personnel with a special cord available form the manufacturer or its authorized 

service personnel in order to avoid a hazard. Improper electrical installation will damage 

electronic components. Damage caused by incorrect electrical connections is not covered 

by warranty.

Summary of Contents for MY CAFE MCA


























Reviews: