Bunn MY CAFE MCA Page 17 Use And Care Manual Download

Page: 17 / 25

8) When the cycle has ﬁnished, empty the container. Repeat step 7 at least two more

times to remove the solution from the tank.

9) Clean the pod holder with a mild detergent and rinse thoroughly.

10) Proceed to the “Cleaning The Sprayhead/Seal” section.

CLEANING THE SPRAYHEAD/SEAL

1) Press the Power Switch into the off “O” position.

2) Unplug the brewer and allow it to cool down. (Minimum of 1 hour.)

3) After the unit has been allowed to cool, remove the pod holder

and set aside.

4) Using your ﬁngers, rotate the sprayhead/seal assembly

clockwise until the sprayhead and seal are removed.

NOTE:

If the sprayhead and seal are separated, they must be

reassembled as they were when removed from the brewer.

CAUTION:

Improper reassembly could result in personal injury

from scalding water.

NOTE:

See “Assembling Sprayhead/Seal” (Page 17) & “Inspecting

Sprayhead Seal” (Page 18) for more information.

5) Clean the sprayhead and seal with a mild detergent and rinse thoroughly.

6) Using your ﬁngers, rotate the sprayhead/seal assembly counter-clockwise until it is

ﬁnger tight.

7) Replace the pod holder.

8) Plug in the brewer and press the Power Switch to restore power to the brewer.

ASSEMBLING THE SPRAYHEAD/SEAL

If the sprayhead and seal are separated during removal or cleaning, they must be

reassembled properly.
1) Identify the top of the seal. The top of the seal that seats

against the roof of the sprayhead ramp has a rough ridge that

can be felt by running your ﬁngers across the surface of the

seal. The bottom is smooth.

2) Identify the top of the sprayhead. The top of the sprayhead

has a star pattern and a threaded hole where the sprayhead

attaches to the brewer.

3) While carefully stretching the seal, guide the sprayhead into

the channel of the seal. Make sure it is completely in the

channel.

When properly assembled, the sprayhead will slide easily into

the channel of the seal and will not cause any buckles in the surface

of the seal. If the sprayhead seems to be difﬁcult to seat, and you

must stretch the seal more than a slight tug, the assembly is not

together correctly.

CAUTION:

Improper reassembly could result in personal injury

from scalding water.

Top

P2953

PERIODIC CLEANING/DESCALING (Cont.)

P3015

Summary of Contents for MY CAFE MCA


























Search results

Summary of Contents for MY CAFE MCA

Reviews:

Related manuals for MY CAFE MCA

Brands by name

Popular brands

Bunn MY CAFE MCA, Use And Care Manual

Search results

Summary of Contents for MY CAFE MCA

Reviews:

Related manuals for MY CAFE MCA

Brands by name

Popular brands