background image

Photoplotter FilmStar-PLUS
Instructions to Use

Page 16 / 16

Guarantee

All machines are submitted before distribution to examination on function and continuous operation 
firmness. On the machine we grant a work warranty of 12 months to our customers starting from pur-
chase date on accuracy in material and processing. We warrant at our choice by exchange of incorrect 
parts or by repair of the machine in our house. Old parts change into our possession. 

Disclaimer of warranty

All parts subjected to wear are excluded from this warranty. Any direct or indirect damage resulting 
from over-heat or chemical reaction shall void all warranty claims. This also applies to defects to the 
machine caused by non-observance of this manual or of parts of it. Unauthorized repairs or interven -
tions to the machine will result in the loss of all warranty claims.
We cannot accept subsequent claims from damage or destruction of workpieces worked on in the ma-
chine, because we have no knowledge or control over the operating conditions at your site. This is valid 
in a general manner also for requirements from damage to articles, buildings and persons as well as  
the environment. 
We do not warrant that the function of the machine will meet the customer's requirements or that the 
operation of the machine will to this regard be error free.
In no event will we be liable to the customer for any incidental, consequential, or indirect damages of  
any kind, including loss of profit and prosecution for environmental pollution, even if we could have  
been aware of the possibility of such damages.
All information was arranged with great care. We reserve ourselves however mistake and technical 
changes without previous announcement.

Copyright

(C) 2013 Bungard Elektronik

Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany

Tel.: +49 2292 / 9 28 28-0, Fax: +49 2292 / 9 28 28-29

, E-mail: [email protected]

Summary of Contents for FilmStar-PLUS

















Reviews: