background image

Free-Air® Pumps 

User Manual

www.bullard.com

General Information

Bullard Free-Air Pumps transfer ambient air from a clean air location, 
where breathable air can be assured at all times, to workers wearing 
Type C or CE continuous flow supplied air respirator hoods or tight 
fitting half- or full-face masks.

The ambient air is filtered through a medium efficiency inlet filter and 
a CARBOFINE Outlet Filter before entering the respirator’s air supply 
hose.

Bullard Free-Air Pumps are oil-less and have rotary carbon vanes. 
They produce no carbon monoxide, oil vapors, oil mist or moisture. 
They do not require expensive carbon monoxide monitors, high 
temperature alarms or airline filters. No calibration is required.
Read all instructions before using your Free-Air pump.

This manual provides detailed instructions, warnings and other information for individuals using Bullard Free-Air Pump 

models EDP30 and EDP50

General Information

 ......................................................................1

Warnings

 ............................................................................................2

Number of Respirators that can be used with Pumps

 .........3

Brathing Air Requirements 

Air Quality ............................................................................................4

Assembling the Free-Air Pump

Electric Motor Specifications  ..............................................................5 
Pump Performance Specifications  ......................................................5

Operating the Free-Air Pump

  ................................................. 6-7

Maintaining the Free-Air Pump

 ..................................................8

Trouble Shooting Guide

 ................................................................9

Replacement Parts and Accessories

 ........................................10

Warranty

 ..........................................................................................11

Return Policy and Return Authorizations

 ............................. 11

Air Filter Replacement Schedule

 ............................................. 12

Table of Contents

EDP30

EDP50

Distributed By:

Summary of Contents for EDP30













Reviews: