Buick 2004 LeSabre Owner'S Manual Download Page 257

Page: 257 / 392

2. Remove the air intake hose that is snapped over

the throttle body by pulling the hose upward and
away from the throttle body which is located
near the top of the engine.

3. Disconnect the

electrical connector
from the air intake
hose. This will allow
you to lift the rear
portion of the engine
air cleaner/filter
housing.

4. After detaching the hose from the throttle body, pull

back the entire rear portion of the engine air
cleaner/filter housing by pulling upward and
rearward.

5-19

Summary of Contents for 2004 LeSabre









































































































































































































































































































































































































Search results

Summary of Contents for 2004 LeSabre

Reviews:

Related manuals for 2004 LeSabre

Brands by name

Popular brands

Buick 2004 LeSabre, Owner'S Manual

Search results

Summary of Contents for 2004 LeSabre

Reviews:

Related manuals for 2004 LeSabre

Brands by name

Popular brands