Buick 2004 LeSabre Owner'S Manual Download Page 126 | Manualshive

Page: 126 / 392

background image

Twilight Sentinel

®

Twilight Sentinel

®

turns your headlamps on and off by

sensing how dark it is outside.

The lever for this feature is
located to the left of the
steering column.

To operate it, leave the exterior lamp button off.

If you slide the lever all the way to MAX, your
headlamps will remain on for about three minutes after
you turn off your engine. As you slide the lever
toward OFF, the headlamps will turn off more quickly.
You can change this delay time from only a few seconds
to three minutes.

The exterior lamps can be completely shut off while the
vehicle is in PARK (P) by sliding the Twilight
Sentinel

®

lever all the way to OFF. To turn the exterior

lamps back on, slide the lever toward MAX again,
or shift out of PARK (P).

Park Lamp Override Feature

If the Twilight Sentinel

®

lighting is active, it can be

disabled by turning on the manual parking lamps. The
lighting will be disabled until the ignition is moved from
RUN or until the outside light level becomes daylight. The
outside light level changing to daylight will cause the
Twilight Sentinel

®

feature to deactivate. The

wiper-activated headlamps will override the twilight
disable feature.

Light Sensor

Your Twilight
Sentinel

®

and DRL work

with the light sensor
located on top of the
instrument panel.

Do not cover it up. If you do, the sensor will read “dark”
and the Twilight Sentinel

®

lighting will turn on.

3-16

«
...
124
125
126
127
128
...
»

Summary of Contents for 2004 LeSabre









































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2004 LeSabre

Brand: Feniex Pages: 6

Brand: Ford Pages: 12

Brute Strength 12057.0271

Brand: Quadratec Pages: 6

YARIS LIFTBACK 2009

Brand: Toyota Pages: 13

Brand: Westfalia Pages: 71

Brand: TAUBENREUTHER Pages: 8

Brand: Whispbar Pages: 15

1506-PHX Cargo Plus

Brand: Ranger design Pages: 8

Brand: AUTOTECH Pages: 1

Brand: KEKO Pages: 3

Brand: Movon Pages: 43

Brand: ConWys AG Pages: 16

Powerbuilt 648601

Brand: AllTrade Pages: 3

SportQuest Series

Brand: Perrycraft Pages: 2

Brand: Edelbrock Pages: 2

Brand: Cadillac Pages: 339

Brand: Curt Manufacturing Pages: 4

MagicWatch MWE850

Brand: Waeco Pages: 200

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands