background image

TC-Double (+) X2

Contents

1

Introduction.....................................................................................................................................................................................................................  3
1.1

Intended use .........................................................................................................................................................................................................  3

1.2

Overview ................................................................................................................................................................................................................  3

1.3

Type plate .............................................................................................................................................................................................................. 4

1.4

Scope of delivery .................................................................................................................................................................................................. 4

1.5

Ordering instructions ........................................................................................................................................................................................  5
1.5.1

TC-Double X2.......................................................................................................................................................................................... 5

1.5.2

TC- X2 ......................................................................................................................................................................................  6

2

Safety instructions.........................................................................................................................................................................................................  7
2.1

Important notices................................................................................................................................................................................................  7

2.2

General hazard warnings ................................................................................................................................................................................. 8

3

Transport and storage ................................................................................................................................................................................................  10

4

Installation and connection .......................................................................................................................................................................................  11
4.1

Installation site requirements........................................................................................................................................................................  11

4.2

Installation ...........................................................................................................................................................................................................  11
4.2.1

Flow adapter connection (optional)............................................................................................................................................... 11

4.2.2

Connecting the moisture detector (option)................................................................................................................................. 11

4.2.3

Connecting the peristaltic pump (option) ................................................................................................................................... 11

4.2.4

Sample gas pump connection gas lines (optional) ..................................................................................................................  12

4.2.5

Connecting the heat exchanger .....................................................................................................................................................  12

4.3

Electrical connections ....................................................................................................................................................................................... 13

4.4

Signal outputs ....................................................................................................................................................................................................  14

5

Operation and control ................................................................................................................................................................................................  16
5.1

Description of functions..................................................................................................................................................................................  16

5.2

Use of menu functions ..................................................................................................................................................................................... 17
5.2.1

Lock Menu.............................................................................................................................................................................................  17

5.2.2

Menu navigation overview.............................................................................................................................................................. 18

5.3

Description of menu functions ....................................................................................................................................................................  20
5.3.1

Main menu ..........................................................................................................................................................................................  20

5.3.2

Submenu 1 ...........................................................................................................................................................................................  20

5.3.3

Submenu 1 (Global Settings) ...........................................................................................................................................................  21

5.3.4

Set favourite menu ...........................................................................................................................................................................  24

6

Maintenance..................................................................................................................................................................................................................  25

7

Service and repair......................................................................................................................................................................................................... 26
7.1

Troubleshooting ................................................................................................................................................................................................ 26
7.1.1

Error messages on the display ........................................................................................................................................................ 27

7.2

Safety instructions ............................................................................................................................................................................................ 28

7.3

Cleaning and removal of the heat exchanger........................................................................................................................................... 29

7.4

Replacing the hoses of the peristaltic pump (option) ............................................................................................................................ 29

7.5

Replacing the filter element (option) .......................................................................................................................................................... 29

7.6

Drying of the moisture detector (option)................................................................................................................................................... 30

7.7

Calibration of the moisture detector (option) .......................................................................................................................................... 30

7.8

Replacing sample gas pump inlet and outlet valves (optional) .......................................................................................................... 30

7.9

Replacing the O-ring on the bypass valve (optional) ............................................................................................................................... 31

7.10 Replacing the bellow (optional) ..................................................................................................................................................................... 31
7.11

Spare parts and accessories ...........................................................................................................................................................................  32
7.11.1

Consumables and accessories ........................................................................................................................................................ 32

8

Disposal ...........................................................................................................................................................................................................................  33

9

Appendices..................................................................................................................................................................................................................... 34
9.1

Gas Cooler Technical Data .............................................................................................................................................................................. 34

9.2

Technical Data - Options ................................................................................................................................................................................. 34

9.3

Flow chart ............................................................................................................................................................................................................  35

9.4

Performance curves.......................................................................................................................................................................................... 36

i

Bühler Technologies GmbH

BE440022 ◦ 10/2018

Summary of Contents for TC-Double

























































Reviews: