background image

PAGE  7 

   

Shielding Gas Cylinders Can Explode

 

 

High pressure cylinders can explode if damaged, so treat them carefully.

 

-Never expose cylinders to high heat, sparks, open flames, mechanical shocks or arcs. 
-Do not touch cylinder with MIG gun. 
-Do not weld on the cylinder 
-Always secure cylinder upright to a cart or stationary object. 
-Keep cylinders away from welding or electrical circuits. 
-Use the proper regulators, gas hose and fittings for the specific application. 
-Do not look into the valve when opening it. 
-Use protective cylinder cap whenever possible 

 

 

1.5 

Proper   Care,   Maintenance   and   Repair

   

 

- Always have power disconnected when working on internal components. 

-  Do not touch or handle PC board without being properly grounded with a wrist strap. Put PC board in static 

proof bag to move or ship. 
- Do not put hands or fingers near moving parts such as drive rolls of fan 

   

USE   AND   CARE

   

Do not modify the welder in any way. 

Unauthorized modification may impair the function and/or safety 

and could affect the life of the equipment. There are specific applications for which 
the welder

 

was designed. 

Always check of damaged or worn out parts before using the welder. 

Broken parts will affect the 

operation. Replace or repair damaged or worn parts immediately. 

Store idle welder. 

When not in use, store it in a secure place out of the reach of children. Inspect it for good 

working condition prior to storage and before re-use.

 

 

The Power Indicator Light is on

 when the machine is turned on. 

   

Thermal   Protection   Indicator   Light

   

When the thermal overload indicator is on, it indicates the machine has exceeded the allowable internal 
temperature. The machine automatically turns off welding output but the fan will remain on to cool down the 
internal components. When the internal temperature had decreased, the machine will automatically turn 
welding output back on. 

Summary of Contents for PSTICK80

















Reviews: