background image

PAGE  8 

Current   Adjustment

   

Current adjustment is on the front panel of the machine. It has infinite current output adjustment from 20 to 
75 Amps. 

Positive   Output   Connector

   

This is the connector for the electrode holder and cable, most often, when STICK welding. When this 
machine is used for TIG welding, this connector is for the grounding cable. 

Negative   Output   Connector

   

This is the connector for the ground cable and clamp, most often, when STICK welding. When this machine 
is used for TIG welding, this connector is for the TIG torch. 

Ground   Cable   and   Clamp

   

The ground cable and clamp are attached to the work piece to complete the circuit allowing the flow of current 
needed to weld. 

Welding   Cable   and   Electrode   Holder

   

One end of the cable is connected to the output connectors of the welder. The electrode is held in the 
electrode holder for welding. 

Power   Cord

   

The power cord connects the welder to the 120V volt power supply. 

Plug the 15 amp plug into a 

115V/20Amp receptacle to supply power to the welder. 

 
 

INSTALLATION

   

1.  POWER  REQUIREMENT  -  AC  single  phase  120V  (110-120V),  60  HZ  with  a  20  amp  circuit  breaker  is 
required. DO NOT OPERATE THIS UNIT if the ACTUAL power source voltage is less than 105 volts AC or 
greater than 132 volts AC. 

 

 

 

High   voltage   danger   from   power   source!   Consult   a   qualified   electrician   for   proper   
installation   of   receptacle.   This   welder   must   be   grounded   while   in   use   to   protect   the

   

operator from electrical shock.

 

 

Do not remove grounding prong or alter the plug in any way. Do not use any adapters between the 
welder's power cord and the power source receptacle. Make sure the

 

POWER switch is OFF when connecting your welder's power cord to a properly grounded 
120 VAC, 60 HZ, Single Phase, 20 Amp input power supply. 

 

2. 

EXTENSION  CORD

  -  We  do  not  recommend  an  extension  cord  because  of  the  voltage  drop  they 

produce. This drop in voltage can affect the performance of the welder. If you need to use an extension cord, 
we recommend you check with a qualified electrician and your local electrical codes for your specific area. Do 
not use an extension cord over 25 ft. in length. 

Summary of Contents for PSTICK80

















Reviews: