Buderus Logamatic 4121 Operating Instructions Manual Download Page 52

Page: 52 / 88

Extended functions

Logamatic 4121, 4122 and 4126 - Subject to technical modifications.

7.20 Room temperature matching

The factory setting is 0 °C. The possible correction range is b5 °C and

-5 °C.

Example:

Displayed room temperature 22 °C, actual room temperature 22.5 °C

Open flap

Simultaneously press and then release "Display" and "Temp".

The display shows "Calibration MEC".

Hold down "Temp" and turn the rotary selector to the required value

(here: "0.5°C").

The display shows the set value.

Release "Temp" to save your input.

Press "Back" to return to the permanent display.

The display shows the corrected temperature (22.5 °C).

USER INFORMATION

This function is only available if the MEC2 is fitted within the living space. If the
room temperature shown on the display varies from the actual temperature
measured with a thermometer, the display value can be adjusted using
"Calibration MEC".

Calibration MEC

Correction

Room temperature

0.0°C

Calibration MEC

Correction

Room temperature

0.5°C

Summary of Contents for Logamatic 4121

























































































Search results

Summary of Contents for Logamatic 4121

Reviews:

Related manuals for Logamatic 4121

Brands by name

Popular brands

Buderus Logamatic 4121, Operating Instructions Manual

Search results

Summary of Contents for Logamatic 4121

Reviews:

Related manuals for Logamatic 4121

Brands by name

Popular brands