Buderus Logamatic 4121 Operating Instructions Manual Download Page 21

Page: 21 / 88

Standard functions

Logamatic 4121, 4122 and 4126 - Subject to technical modifications.

6.3.1 Selecting automatic mode

In automatic mode your heating system will operate with the time switch
program, i.e. central and DHW heating at preset times.

Example: Enabling automatic mode

Press "AUT".

The "AUT" LED illuminates; automatic mode is enabled.

In addition, either the "Day mode" or the "Night mode" LED will illuminate. This is
subject to the set times for day and night mode.

Automatic day and night mode

At fixed times, central heating is provided or the room temperature is set back.

AUT

Set room

Automatic day

21°C

Fig. 8

Changeover from day and night mode at fixed times (example)

Day mode

Night mode

7 747 012 053-18.1RS

05:30

22:00

21 °C

17 °C

Summary of Contents for Logamatic 4121

























































































Search results

Summary of Contents for Logamatic 4121

Reviews:

Related manuals for Logamatic 4121

Brands by name

Popular brands

Buderus Logamatic 4121, Operating Instructions Manual

Search results

Summary of Contents for Logamatic 4121

Reviews:

Related manuals for Logamatic 4121

Brands by name

Popular brands