Buderus Logamatic 4121 Operating Instructions Manual Download Page 24

Page: 24 / 88

Standard functions

Logamatic 4121, 4122 and 4126 - Subject to technical modifications.

6.4.2 For the operating mode not currently enabled

You may also adjust the room temperature for an operating mode that is
not currently enabled.

For example, you are currently in automatic day mode and would like to alter
the set night temperature.

Hold down "Night mode", and select the required night room temperature with
the rotary selector (here: "16°C").

Release "Night mode".

The night setback temperature is now adjusted to 16 °C. The selected
permanent display will then appear again.

Press "AUT".

The "AUT" LED illuminates; automatic mode is re-enabled.

Set room

Constant night

16°C

AUT

USER INFORMATION

If you are currently in automatic night mode, and you wish to adjust the day
mode, proceed as described above, but instead hold down "Day mode".

Summary of Contents for Logamatic 4121

























































































Search results

Summary of Contents for Logamatic 4121

Reviews:

Related manuals for Logamatic 4121

Brands by name

Popular brands

Buderus Logamatic 4121, Operating Instructions Manual

Search results

Summary of Contents for Logamatic 4121

Reviews:

Related manuals for Logamatic 4121

Brands by name

Popular brands