BTEK WorldWEIGH BWS Series Technical Manual Download Page 3

Page: 3 / 26

CONTENTS

1. SPECIFICATION... 2
2. INTRODUCTION... 3

Charging...3

3. INSTALLATION. 4

Installation.. 4

Wiring

....

4. KEYS DESCRIPTION... 6

Key Board... 6
Secondary functions of the keys.8

5. OPERATION 8

5.1. Basic Operation... ...8

1.  Power  On  /Off..8
2.  Zero...8
3.  Tare...8
4.  Select  Unit8

5.2. Check Weighing..9

5.2.1. Set Limits......9
5.2.2. Set Check Weighing...9

5.3. Accumulation10

5.3.1.  Memory Recall.....10
5.3.2.  Memory Clear...10
5.3.3.  Automatic  Accumulation...11

5.4.  Parts  Counting.....11
5.5.  Animal Weighing..12
5.6.  Key Board Lock12
5.7.  Set Auto Power Off..13
5.8.  Set Back Light..13

6. PARAMETERS.14
7.

CALIBRATION

8. RS-232 OUTPUT19

8.1.  Specifications.19
8.2.  Connecter19
        RS-232  Output19
8.3.  Continuous  output  protocol.19

9. DRAWING20

9.1.

BWS Drawing20

9.2.

BWS Parts List..21

10. ERROR CODES..22

Summary of Contents for WorldWEIGH BWS Series



























Search results

Summary of Contents for WorldWEIGH BWS Series

Reviews:

Related manuals for WorldWEIGH BWS Series

Brands by name

Popular brands

BTEK WorldWEIGH BWS Series, Technical Manual

Search results

Summary of Contents for WorldWEIGH BWS Series

Reviews:

Related manuals for WorldWEIGH BWS Series

Brands by name

Popular brands