BTEK WorldWEIGH BWS Series Technical Manual Download Page 25

Page: 25 / 26

BWS Series Indicator Technical Manual

- 22 -

10. ERROR CODES

Error Message

Description

Solution

-----

Maximum load exceeded

Unload or reduce weight.

Err L

Low reading

Re-check wiring

Err 4

Zero setting error

Zero setting range exceeded
due to switching on.(4%max)
Make sure platform is empty.

Err 5

Key board error

Check the keys and connecter.

Err 6

A/D value out of range

Make sure platform is empty.
Check the load cell connectors.

Err 9

Unstable Reading

Check any air variation,
vibration, RF noise and
binding somewhere.
Check the load cell and
connecters.

Err 1

Err 1 7777

Tare out of range

Remove the load and restart
scale again.

--ol--

Over range

Remove the load.
Recalibrate

fAIL H

fAIL H
faIL L

faIL L

Calibration Error

Recalibrate

Err p

Printer error

Check the printer and settings.

flashing backlight Battery low

Recharge battery, check the
voltages.

Ba LO

LO ba

Battery low

Recharge battery, check the
voltages.

Summary of Contents for WorldWEIGH BWS Series



























Search results

Summary of Contents for WorldWEIGH BWS Series

Reviews:

Related manuals for WorldWEIGH BWS Series

Brands by name

Popular brands

BTEK WorldWEIGH BWS Series, Technical Manual

Search results

Summary of Contents for WorldWEIGH BWS Series

Reviews:

Related manuals for WorldWEIGH BWS Series

Brands by name

Popular brands