Brymen BM510 Series User Manual Download Page 14 | Manualshive

Page: 14 / 20

background image

13

Relative mode (BM815 & BM817 only)

Relative zero allows the user to offset the meter consecutive measurements with the
displaying reading as the reference value. Practically all displaying readings can be set
as relative reference value including MAX/MIN feature readings. Press the button
momentarily to activate and to exit relative zero mode.

Manual or Auto-ranging

Press the

RANGE

button momentarily to select manual-ranging, and the meter will

remain in the range it was in, the LCD annunciator

turns off. Press the button

momentarily again to step through the ranges. Press and hold the button for 1 second
or more to resume auto-ranging.
Note: Manual ranging feature is not available in Hz function.

Set Beeper Off

Press the

Hz

button while turning the meter on to disable the Beeper feature.

«
...
12
13
14
15
16
...
»

Summary of Contents for BM510 Series





















Reviews:

No comments

Related manuals for BM510 Series

MultiMeter-Compact

Brand: LaserLiner Pages: 26

Brand: UNI-T Pages: 2

METRAHIT IM E-DRIVE

Brand: Gossen MetraWatt Pages: 56

Brand: Gossen MetraWatt Pages: 71

Brand: Gossen MetraWatt Pages: 74

Brand: Keysight Pages: 83

Brand: PeakTech Pages: 40

Brand: YOKOGAWA Pages: 2

Brand: Sam Pages: 41

Brand: Wavetek Pages: 44

Brand: Canoga Perkins Pages: 50

Brand: UNI-T Pages: 42

Brand: Omega Pages: 14

Brand: Keithley Pages: 44

Brand: FMUser Pages: 41

Brand: Feig Electronic Pages: 14

Brand: Vigor Pages: 20

Columbus Triplex

Brand: Vista Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands