background image

RECOMMENDED FUEL AND OIL

Fuel

Vehicles with Valid Warranty (pre-heat switch disabled)

Use premium unleaded gasoline, available from most service
stations or oxygenated fuel containing a maximum total of 10%
of ethanol or methanol or both. The gasoline used must have the
following recommended minimum octane number.

LOCATION

OCTANE NUMBER

Inside North America

(91 (RON + MON)/2)

Outside North America

95 RON

Vehicles without Warranty (pre-heat switch enabled)

Use racing fuel with the following octane number.

MINIMUM

LOCATION

OCTANE NUMBER

Inside North America

(108 (RON + MON)/2)

Outside North America

113 RON

RECOMMENDED

LOCATION

OCTANE NUMBER

Inside North America

(114 (RON + MON)/2)

Outside North America

119 RON

NOTE:

The fuel tank cap specifies an octane number of 91 as a min-

imum. A higher octane number is required in racing application.

All Vehicles

CAUTION: Never experiment with other fuels. The use of unrec-
ommended fuel can result in snowmobile performance deterio-
ration and damage to critical parts in the fuel system and engine
components.

__________________________

9

Summary of Contents for Ski-Doo MX Z X 440 2007































Reviews: