BRP Sea-Doo GTX 170 2022, Operator'S Manual, Page: 123 / 204

121
oil additives may not be covered by
the BRP Limited Warranty.
E En ng giin ne e O Oiill L Le evve ell
N NO OT TIIC CE E
O Op pe erra attiin ng g tth he e e en ng giin ne e w wiitth h a an n iim m--
p prro op pe err lle evve ell m ma ayy sse evve erre ellyy d da am m--
a ag ge e e en ng giin ne e..
C CA AU UT TIIO ON N
M Ma an nyy cco om mp po on ne en nttss iin n tth he e e en ng giin ne e
cco om mp pa arrttm me en ntt m ma ayy b be e vve erryy h ho ott.. D Dii--
rre ecctt cco on ntta acctt m ma ayy rre essu ulltt iin n sskkiin n
b bu urrn n..
IIff W Wa atte errccrra afftt iiss O Ou utt o off tth he e W Wa atte err
N NO OT TIIC CE E
W Wa atte errccrra afftt m mu usstt b be e lle evve ell..
C CA AU UT TIIO ON N
W Wh he en n o op pe erra attiin ng g tth he e e en ng giin ne e w wh hiille e
tth he e w wa atte errccrra afftt iiss o ou utt o off w wa atte err,, tth he e
h he ea att e exxcch ha an ng ge err iin n tth he e rriid de e p plla atte e
m ma ayy b be ecco om me e vve erryy h ho ott.. A Avvo oiid d a an nyy
cco on ntta acctt w wiitth h tth he e rriid de e p plla atte e a ass
b bu urrn nss m ma ayy o occccu urr..
1. Raise trailer tow pole, then block in
position when bumper rail is level.
2. Install a garden hose on the ex-
haust system flushing connector.
Refer to
Exhaust System in this
section and follow the procedure.
N NO OT TIIC CE E
N Ne evve err rru un n e en ng giin ne e w wiitth ho ou utt ssu up pp pllyy--
iin ng g w wa atte err tto o tth he e e exxh ha au usstt ssyysstte em m..
F Fa aiillu urre e tto o cco oo oll e exxh ha au usstt ssyysstte em m
m ma ayy sse evve erre ellyy d da am ma ag ge e iitt..N Ne evve err rru un n
e en ng giin ne e llo on ng ge err tth ha an n 2 2 m miin nu utte ess..
D Drriivve e lliin ne e sse ea all h ha ass n no o cco oo olliin ng g
w wh he en n w wa atte errccrra afftt iiss o ou utt o off w wa atte err..
3. Remove the seat(s).
4. Start the engine.
5. Open the water tap.
6. Run the COLD engine at iid dlle e ffo orr
3 30 0 sse ecco on nd dss.
7. Close water tap.
8. Bring engine RPM to 4000-4500
RPM for 15 seconds.
9. Stop the engine abruptly by press-
ing the start/stop button or remov-
ing the tether cord.
10. Wait at least 30 seconds for the oil
to settle in the engine, then pull
dipstick out and wipe clean.
T TY YP PIIC CA AL L
1. Oil dipstick
2. Oil filler cap
11. Reinstall dipstick, push in
completely.
12. Remove dipstick again and read
oil level. It should be between the
FULL and ADD marks.
T TY YP PIIC CA AL L
1. Full
2. Add
3. Operating range
Add oil to ensure the level is be-
tween marks as required.
1. Remove oil cap.
2. Place a funnel in valve cover
opening.
MAINTENANCE PROCEDURES